EDTM TS1320 Manual De Instrucciones página 2

LAMP REPLACEMENT
The TS1320 includes a custom short wave
UV lamp inside the enclosure. If the lamp
stops working, confirm that your batteries
are still functional. If you have replaced the
batteries and installed them correctly (dou-
ble-check polarity) and the instrument is still
not working, it may be necessary for you to
replace the short wave UV lamp. The re-
placement lamp is PART# TS1310 and is
available from your dealer.
To replace the lamp, turn the unit off first.
WARNING: YOU MUST REMOVE THE
BATTERIES BEFORE SERVICING THE
INSTRUMENT. There are dangerous high
voltages present inside the enclosure, and
the electronics should never be touched
when powered. Use a Phillips screwdriver
to remove the four screws of the enclosure.
Please note, two of the screws are located
behind the battery compartment cover.
two
screws
Figure 8: Remove batteries and
four screws from enclosure
RELATED PRODUCTS
"Glass-Chek ELITE"
Identify location and type of low e coatings, as well
as glass, lami & air space thickness. Good for single,
double & triple pane windows. (Model# GC3200)
"STRENGTHENED GLASS DETECTOR"
(Model# SG2700)
Identify strengthened / tempered glass
The body of the lamp is held in place by
foam pieces, while the terminals are insert-
ed into sockets in the circuit board. Care-
fully pull the old lamp out of the sockets.
Pay special attention to the foam pieces as
you may have to peel them away from the
bulb. Leave as much of the foam in place
as possible, as this helps provide shock ab-
sorption to the bulb during use.
Figure 9: Remove the old lamp
and replace with new
The replacement bulb should never be han-
dled with bare fingers. Please use gloves
when handling the replacement bulb. The
replacement bulb will be sent to you with the
terminals crimped at the proper location.
DO NOT MAKE ANY ADJUSTMENTS TO
THE TERMINALS, AS THEY ARE EX-
TREMELY FRAGILE. Carefully press the
lamp terminals into the receptacles. Fully
reassemble the unit before turning power
on to check the new lamp.
two
screws
Remember, DO NOT stare at the lamp out-
put directly. Either look at the image through
a piece of float glass, or put on your UV
blocking safety glasses (included).
Dual Pane Low E CoatingDetector (Model# AE1601)
"The EDGE" Low-E Coating Detector
BATTERY REPLACEMENT
If the low battery indicator illuminates, the
instrument is warning that the batteries
should be replaced in the near future. It is
possible that the TS1320 product will con
tinue to work for some time after the indi
cator illuminates. It is totally safe to continue
using the instrument while the low battery
indicator is illuminated. Monitor the intensi
ty of the lamps to know the exact time that
the batteries need replaced. The TS1320 is
powered by three AA alkaline batteries.
Alkaline batteries are required for the best
performance of this device. Before replac
ing the batteries, be sure to turn the power
off. To access the batteries, you must first
remove the rubber boot from the product.
Next you can remove the battery cover on
the back side of the enclosure by pressing
your thumb in the center of the battery cover
and sliding the removable lid off. Replace
the batteries and install the cover. Be sure
to install the batteries correctly (polarity +/-).
A battery polarity indicator is included inside
the battery compartment. Installing the bat-
teries backwards may cause permanent
damage to the lamp and will not be covered
by the product warranty. If the unit is going
to be stored for more than a month, we rec-
ommend removing the batteries during stor-
age.
"ETEKT+"
(Model# CM2030)
Low-E coating & edge deletion detector
2
REPLACEMENT PARTS
PART # DESCRIPTION
TS1310 Replacement Lamp
TS1317 Replacement Rubber Boot
WARRANTY
The manufacturer warrants the electronics included
in all models of the TS1320 to be free from defects
in material and workmanship under normal use and
service as specified within the operator's manual. The
manufacturer shall repair or replace the unit within
twelve (12) months from the original date of shipment
after the unit is returned to the manufacturers factory,
prepaid by the user, and the unit is disclosed to the
manufacturers satisfaction, to be thus defective. This
warranty shall not apply to any unit that has been re-
paired or altered other than by the manufacturer. The
aforementioned provisions do not extend the original
warranty period of the unit which has been repaired
or replaced by the manufacturer. Batteries, lamps,
rubber boots, stencils and front panel interface com-
ponents are not covered by warranty.
- The manufacturer assumes no liability for the conse-
quential damages of any kind through the use or mis-
-
use of the TS1320 product by the purchaser or others.
No other obligations or liabilities are expressed or im-
plied. All damage or liability claims will be limited to an
- amount equal to the sale price of the TS1320, as es-
tablished by the manufacturer.
DIGITAL Tin Side Detectors
(Model# TS2300)
"LOW-E CARD" & "LOW-E CARD+"
(Model# AE2200 & AE2250)
Credit card size low-E detector