Adjusting The Height; Timer Function - Black+Decker BXEFP50E Manual De Instrucciones

ENGLISH
♦ Put the battery in its compartment, respecting the
polarity.
Assembling the FAN:
♦ Attach the bottom tube (N) to the base (O) and fix it with
the plastic nut (P).
♦ Loosen the tube-fixing bolt (M) and carefully pull up the
adjustable tube (L). Tighten the bolt (M) again so the
adjustable tube is fixed at its highest position.
♦ Loosen the bolt (J) on the fan head. Fit the fan head (H)
and the adjustable tube (L) together and tighten the bolt
(J) again.
♦ Remove the grill (D) and blade fasten nut (B) from the
motor shaft (F).
♦ Attach the back grill (E) to the motor cover (G) and fix it
with the grill fasten nut (D).
♦ Attach the blades to the motor shaft (F) and fix it with the
blade fasten nut (B).
♦ Attach the front grill (A) to the back grill (E). Use the grill
ring to carefully hold them together and lock them using
the screw provided on the grill buckle.
♦ Check the correct functioning of the fan.

ADJUSTING THE HEIGHT:

♦ The height of this fan can be adjusted from approximate-
ly 110cm to 135cm.
♦ To adjust the height simply loosen the tube fixing bolt
(M). Move the adjusting tube (L) to the desired position
and tighten the bolt (M) again.
INSTRUCTIONS FOR USE
Before use:
♦ Make sure that all products' packaging has been
removed.
♦ Prepare the appliance according to the function you wish
to use:
Use:
♦ Extend the cable completely before plugging it in.
♦ Connect the appliance to the mains.
♦ Turn the appliance on, by using the on/off button (7/e).
♦ Select the desired speed.
Fan function:
♦ Select the desired ventilation speed by pressing the
speed button (6/a).
♦ The selected speed will appear on the LED display (1).
6
(Original instructions)

Timer function:

♦ The appliance's operating time can be controlled (1-
15h).
♦ To program the operating time simply select it using
the timer button (4/c). For every press the time will be
increased 1 hour.
♦ The time programmed will appear on the LED display
(1), and the timer pilot light will turn on.
♦ After the selected time the appliance will switch off
automatically.
Oscillation function:
♦ The oscillation function makes it possible to direct the
flow from the apparatus so that it automatically alter-
nates over a range of approximately 85º.
♦ To activate this function, press the oscillation button
(3/d).
♦ The oscillation pilot light will turn on.
♦ To deactivate this function, follow the procedure for
switching it on in reverse.
WIND MODES:
♦ This model has three wind modes:
♦ Normal: The fan operates constantly at the selected
speed.
♦ Breeze: The fan alternates periods of more and less
power, simulating the feeling of a soft breeze. The
amplitude of these shifts depends on the speed selected.
♦ Night: When the fan is at speed 3, it runs at speed 3
for 30 minutes, then at speed 2 for 30 mor minutes and
finally at speed 1 until it is turned off or timer runs out.
When the fan is at speed 2, it runs at speed 2 for 30
minutes and then it keeps running at low speed until it is
turned off or timer runs out. When the fan is at speed 1,
it simply keeps running at speed 1 until it is turned off or
timer runs out.
♦ To activate this function, press the modes button (5/b).
The modes pilot lights will show which mode is selected.
♦ To deactivate this function, follow the procedure for
switching it on in reverse.
Once you have finished using the appli-
ance:
♦ Turn the appliance off using the on/off button (7/e).
♦ Unplug the appliance from the mains.
♦ Clean the appliance.