Know Your Product; Operation; Prior To Initial Operation - SPARKY MBS 976 Instrucciones De Uso Originales

force in your area. The same applies for general
rules of occupational health and safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
Even when the tool is used as prescribed it is not
possible to eliminate all residual risk factors. The
following hazards may arise in connection with the
tool's construction and design:
▪ Damage to the lungs if an effective dust mask
is not worn.
▪ Damage to hearing if effective earmuffs are
not worn.
▪ SPARKY power tools must not be used out-
doors in rainy weather, or in moist environment
(after rain) or in close vicinity with easily flam-
mable liquids and gases. The working place
should be well lit.
V - Know your product
Before using the power tool, familiarize yourself
with all the operating features and safety require-
ments.
Use the tool and accessories only for the applica-
tions intended. All other applications are expressly
ruled out.
1. Front handle
2. Main handle
3. Dust collection bag
4. Lock-on button
5. On/Off switch
6. Drive roller
7. Sanding belt tension lever
8. Front belt roller
9. Belt rotation direction indicator
10. Tracking adjustment knob
11. Dust extraction port
12. Electronic regulator of speed (MBS 976Е)
13. Slots for fixing the sanding frame
14. Sanding frame (sold separately)
15. Thermoplastic elastolan (TPE) pad (sold
separately)
16. Fixing clamps (sold separately)
17. Mounting holes
VI - Operation
These models SPARKY power tools are sup-
plied from single-phase alternating current mains.
They are double insulated according to EN 60745,
IEC 60745 and can be connected to grounded or
6
EN
not grounded sockets. This power tool is radio
suppressed in compliance with EMC Directive
2004/108/EC.

pRioR to iNitial opERatioN

WaRNiNg: Make sure power supply
voltage corresponds to the value indicated on
the name plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected to the power
supply socket only when this switch is in OFF
position. If the plug is connected to a recepta-
cle while the power switch is in the ON position,
the power tool will start operating immediately,
which could cause a serious accident.
▪ Make sure the cord and the plug are in order.
If the replacement of the supply cord is neces-
sary, this has to be done by the manufacturer or
his agent in order to avoid a safety hazard.
sWitcHiNg oN - sWitcHiNg off
brief activation: (Fig. 1)
Switching on: press ON/OFF switch (5).
Switching off: release ON/OFF switch (5).
continuous use: (Fig. 2)
Switching on: press ON/OFF switch (5) and in
pressed position lock it by button (4).
Switching off: press ON/OFF switch (5) once and
release it immediately.
attacHiNg a saNDiNg bElt
WaRNiNg: Switch off the sander and
disconnect it from the power point.
1. Pull the belt tension lever (7) and slide off the
old belt. (Fig. 3)
2. Check that the replacement belt has a good join
and is not frayed at the edges.
3. Slip the new belt into position with the rotation
arrow on the inside of the belt pointing in the
same direction as the arrow on the sander.
(Fig. 4)
4. Fold down the lever (7). (Fig. 5)
5. Plug the sander into a power point and with the
sander held tight, pull the trigger on/off switch
(5) and allow the belt to rotate for a short period.
6. Whilst the belt is running, adjust the tracking
knob (10) to align the belt to the centre of the
roller (6). (Fig. 6)
7. Repeat the trigger action and tracking adjust-
MBS 976 • MBS 976E