Maintenance; Warranty - SPARKY MBS 976 Instrucciones De Uso Originales

tionary use.
▪ Place the rubber pad (15) on the bench as indi-
cated by the inscriptions. Never mount the ma-
chine onto the bench without the rubber pad.
▪ Turn the machine upside down and centre it on
the rubber pad. The mounting holes (17) shall
face towards the operator.
▪ Insert the mounting pins of the clamps (16) into
the mounting holes (17).
▪ Use the clamps (16) to fasten the machine onto
the bench.
▪ Tighten the clamps with the wing nuts by hand.
Make sure the clamps are tightened properly
but do not over tighten.
▪ Make sure the machine is securely fastened to
the bench before switching the machine on.
The machine can be set to continuous operation
by means of the lock-on button (4).
moUNtiNg tHE saNDiNg fRamE
The wide footprint of the sanding frame enables
the entire assembly to glide over uneven surfaces
and prevents sander tilting and gouging.
When flatness is important and the surface is
large, like a floor or a table top, always use the
sanding frame.
Put the sanding frame (14) on the machine and
insert the four straps into the slots (13). (Fig. 10)
Rotate the knurled adjustment bolt at the rear of
the sanding frame (14) to fasten or release the
frame. (Fig.11)
accEssoRiEs
mbs 976: Dust bag, 80 grit sanding belt fitted on
the machine.
mbs 976E: Dust bag, 80 grit sanding belt fitted on
the machine, set of 4 assorted sanding belts (60
grit - 2 pcs., 80 grit - 1 pc, 120 grit - 1 pc)
VII - Maintenance
WaRNiNg: Always ensure that the tool
is switched off and unplugged before attempt-
ing to perform inspection or maintenance. Reg-
ularly check that all the fixing screws are tight.
They may vibrate loose over time.
Re-lubricate all moving parts at regular intervals.
bRUsH REplacEmENt
When the carbon brushes are worn out, both
brushes must be replaced simultaneously with
genuine brushes at SPARKY service centre for
8
EN
warranty and post-warranty service.
clEaNiNg
For safe operation always keep the machine and
its ventilation slots clean. Regularly check to see
if any dust or foreign matter has entered the grills
near the motor and around the switches. Use a
soft brush to remove any accumulated dust. Wear
safety glasses to protect your eyes whilst clean-
ing.
If the body of the tool needs cleaning, wipe it with a
soft damp cloth. A mild detergent can be used.
WaRNiNg: Never use alcohol, petrol or
other cleaning agent. Never use caustic agents
to clean plastic parts.
WaRNiNg: Water must never come
into contact with the tool.
impoRtaNt: To assure product safety and reli-
ability, repairs, maintenance and adjustment (in-
cluding brush inspection and replacement) should
be performed by certified service centres or other
qualified service organisations, always using gen-
uine replacement parts.
VIII - Warranty
The guarantee period for SPARKY power tools is
determined in the guarantee card.
Faults due to normal wear, overloading or improp-
er handling will be excluded from the guarantee.
Faults due to defective materials implemented as
well as defects in workmanship will be corrected
free of charge through replacement or repair.
The complaints for defective SPARKY power
tools will be recognized if the machine is sent
back to the dealer or is presented to the author-
ised warranty service centre undismantled, in its
initial condition.
Notes
Carefully read the entire original instructions be-
fore using this product.
The manufacturer reserves the right to make
changes and improvements to the products and
to alter specifications without prior notice.
Specifications may differ from country to country.
MBS 976 • MBS 976E