Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation
Instructions
BEFORE YOU BEGIN
STOP
Read these instructions completely
and carefully.
IMPORTANT
tions for local inspector's use.
IMPORTANT
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
with your Owner's Manual for future
reference.
WARNING:
To prevent electric shock, disconnect electri-
cal power supply to dishwasher before
changing panels. Do not operate dishwasher
while changing panel.
CAUTION:
On new installations, do not remove wood
base until you are ready to install the dish-
washer. The dishwasher will tip over when
the door is opened.
1 CUT 1/4" THICK CUSTOM
PANEL TO SIZE
• Cut door panel to the dimensions shown in
Figure 1.
NOTE: The trim provided will conceal the cut
edges of the panel.
– Save these instruc-
– Observe all governing
1/4" Custom Dishwasher
Door Panel Kit
GPF825 Series Kits
GPF825B-Black Trim Kit,
GPF825C-Bisque Trim Kit, GPF825W-White Trim Kit
TOOLS AND MATERIALS REQUIRED:
• Stubby Phillips screwdriver
• Gloves to protect against sharp edges
• Safety glasses
KIT INCLUDES:
• Door panel frame
• 2 Door springs
Top
Trim
Adjustable
Steel Panel
Fully Assembled Door Panel Frame
Figure 1
Side Trim
Bottom
2 Door Springs
Trim
To Be Used On All Models
Except PDW8500
1/4" Thick
Door Panel
23-1/2"
25-1/16"
Publicidad
Manuales relacionados para GE GPF825 Serie
Resumen de contenidos para GE GPF825 Serie
- Página 1 1/4" Custom Dishwasher Installation Door Panel Kit GPF825 Series Kits Instructions GPF825B-Black Trim Kit, GPF825C-Bisque Trim Kit, GPF825W-White Trim Kit TOOLS AND MATERIALS REQUIRED: BEFORE YOU BEGIN STOP • Stubby Phillips screwdriver Read these instructions completely • Gloves to protect against sharp edges and carefully.
- Página 2 2 REMOVE DOOR PANEL Bottom Phillips Screws Figure 2 Figure 3 • Open dishwasher door. • Remove the two screws on the bottom of the • Remove the 6 Phillips head screws along the door panel (Figure 3). Retain screws. sides of the door (Figure 2) holding the inner •...
-
Página 3: Before You Begin
4 INSTALL THE ASSEMBLED PANEL Escutcheon Slot Bottom Figure 9 Phillips Screws Figure 7 Figure 8 • Close the dishwasher door. • Open the dishwasher door and reinstall the • Slide the panel assembly into the escutcheon original 6 Phillips head screws to hold the inner tab (Figure 7). - Página 4 5A TEST DOOR BALANCE Note: To increase tension, use FOR MODEL PDW8500 ONLY top hole. To decrease tension use lower hole. Adjust both • Release door latch. Open and release the springs to the same tension door. If the door tends to drop when released, setting to correct balance.
- Página 5 Juego de panel personalizado de 1/4 de pulg. (6 mm) para puerta de Instrucciones lavavajillas de instalación Juegos de la serie GPF825 GPF825B, Juego de molduras negras GPF825C, Juego de molduras esmaltadas GPF825W, Juego de molduras blancas ANTES DE COMENZAR HERRAMIENTAS Y MATERIALES PARE REQUERIDOS:...
- Página 6 2 RETIRE EL PANEL DE PUERTA Tornillos Phillips Figura 2 inferiores Figura 3 • Abra la puerta del lavavajillas. • Retire los dos tornillos que están en la parte • Saque los 6 tornillos Phillips de los costados inferior del panel de puerta (Figura 3). Con- de la puerta (Figura 2) mientras sujeta la serve los tornillos.
- Página 7 4 INSTALE EL PANEL ARMADO Pestaña de la lámina Tornillos Figura 9 Phillips inferiores Figura 7 Figura 8 • Cierre la puerta del lavavajillas. • Abra la puerta del lavavajillas y vuelva a • Deslice el conjunto del panel dentro de la atornillar los 6 tornillos Phillips originales para pestaña de la lámina (Figura 7).
- Página 8 5A PRUEBE EL BALANCE DE LA PUERTA Nota: Use el orificio superior MODELO PDW8500 SOLAMENTE para aumentar la tensión. Use el orificio inferior para reducir • Suelte el gancho de la puerta. Abra y suelte la la tensión. Ajuste ambos puerta.