Publicidad
Idiomas disponibles
Idiomas disponibles
ADJUSTING THE GUIDE ARM
1.
Pull out 3 to 4 feet of hose and allow reel to lock in position.
2.
Remove the four bolts connecting guide arm to mounting base.
3.
Rotate guide arm in 90° increments to desired position. (There are a total of 5 positions available.) Replace the four bolts
and tighten.
4.
Choose your required mounting hardware for your application. Mount reel using four 3/8" bolts (minimum Grade 5)
secured through the four slots in mounting base. Use washers on mounting bolts (Bolts and Washers are not
included).
5.
After reel is secured in position, attach air hose coming from compressor. Wrap threads of male connector on incoming air
hose with Teflon tape or thread sealant and connect to air inlet valve on side of hose reel. Connect the other end of
incoming air hose to air compressor. Apply Teflon tape to threads on hose before attaching a quick coupler.
ADJUSTING THE HOSE BALL STOP
The hose ball stop is used to adjust the length of hose that remains outside the reel. To adjust, pull hose out past desired position of
hose ball stop and latch reel. Loosen both bolts and move ball stop to proper position. Tighten bolts.
OPERATING YOUR HOSE REEL
1. Slowly pull hose from reel to desired length. A ratcheting mechanism inside reel makes a short series of clicking sounds every
half revolution of reel.
2. To lock reel in position, listen for clicking sounds as hose is slowly pulled from reel. When reel clicks stop pulling hose. Decrease
tension on hose and reel should lock into position.
3. To retract hose onto reel, slowly pull out hose until series of clicking sounds stops (1/8 revolution) NEVER LET GO OF HOSE!
Allow hose to retract slowly until hose ball stop rests against hose guide.
4. Periodically check the hose for excessive wear and hose connections for air leaks.
ADJUSTING RECOIL TENSION
1. Disconnect incoming air supply.
2. Pull out about 2 feet of hose and latch the reel.
3. Remove hose ball stop.
4. While firmly holding onto edge of reel drum, unlatch reel and carefully allow drum to slowly rewind, drawing hose end back
through guide arm roller assembly and onto reel. Latch reel in position.
5. To Increase Tension: Unlatch reel and turn clockwise (as viewed from air inlet side). To Decrease Tension: Unlatch and allow
reel to rotate slowly counter clockwise (as viewed from air inlet side).
6. Once desired spring tension is reached, latch reel in position. Feed hose end through roller assembly in guide arm and reattach
hose ball stop.
7. Reconnect incoming air supply.
REPLACING THE HOSE
1. Secure and stabilize reel. In most cases, the hose can be replaced with reel mounted in place.
2. Disconnect incoming air supply.
3. Pull out entire length of hose and lock reel. Make sure reel is securely locked in position.
4. Unscrew hose clamps that secure hose to drum. Disconnect inlet end of hose from air inlet valve.
5. Pull inlet-end of hose through slot in drum and guide rollers removing the old hose completely.
6. Remove spring hose guard, hose clamp and hose ball stop from old hose. Fit these parts on to the new hose in identical
positions.
7. Feed inlet-end of hose through guide rollers and slot in drum.
8. Apply Teflon sealant tape or thread sealant to hose connector and connect to air inlet valve.
9. Attach hose clamp to drum. Rewind hose onto reel using normal operation.
Veuillez lire et conserver ces instructions. Lisez bien le manuel avant d'assembler et d'utiliser ce produit. Tout manquement aux
instructions et avertissements pourrait occasionner des blessures et des dommages au produit ou à la propriété. Veuillez prendre note
que les avertissements et instructions dans ce manuel ne sauraient couvrir toutes les conditions et éventualités.
I
'
NSTRUCTIONS D
Félicitations pour l'achat de ce produit Mäktig de qualité !
'
ASSEMBLAGE ET D
UTILISATION
Publicidad
