Ocultar thumbs Ver también para H60K-51D-CH:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

KITCHEN FAUCET
WITH PULL-OUT SPRAY
H60K-51D-CH – Polished chrome finish
H60K-51D-BN – Brushed nickel finish
H60K-51D-ORB – Oil-rubbed bronze finish
PACKAGE AND HARDWARE CONTENTS
PART
DESCRIPTION
A
Faucet body
B
C
Mounting bolt
D
Mounting nut
E
F
Lock nut
G
H
I
J
Sprayhead
K
Deckplate
Due to constant design and quality improvements, the
product inside may look slightly different from the picture.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water supply
lines.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package and hardware contents list. If any part is missing or damaged,
do not attempt to assemble the product. Contact customer service for
replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): adjustable wrench, slip joint pliers,
Phillips screwdriver, supply lines, and silicone
Need Help? Please call our toll-free line at (877) 319-3757 (7:30 am to 4:30 pm CST) for additional assistance or service.
Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • Homewerks.com
QUANTITY
Gasket
Washer
Screw
Flange
Weight
1
1
2
J
2
1
1
K
2
1
1
1
1
CAUTION
• If you solder the joints during installation, the seats, cartridges, and washers
must be removed before using a flame or the warranty will be voided on
these parts.
• Cover the sink drain to avoid losing parts.
Installation may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of the faucet are not
all included; however, they are available wherever plumbing supplies
are sold.
Prior to beginning installation, turn off the hot and cold water lines, then turn
on the old faucet to release built-up pressure. When installing the new faucet,
hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections
that are too tight will reduce the integrity of the system.
A
B
C
H
E
F
D
G
I
10-29-2020

Publicidad

Tabla de contenido

Solución de problemas

loading

Resumen de contenidos para Home2O H60K-51D-CH

  • Página 1 KITCHEN FAUCET WITH PULL-OUT SPRAY H60K-51D-CH – Polished chrome finish H60K-51D-BN – Brushed nickel finish H60K-51D-ORB – Oil-rubbed bronze finish PACKAGE AND HARDWARE CONTENTS PART DESCRIPTION QUANTITY Faucet body Gasket Mounting bolt Mounting nut Washer Lock nut Screw Flange Weight...
  • Página 2: Product Specifications

    PRODUCT SPECIFICATIONS Maximum Flow Rate: 1.8 GPM (6.8 LPM) at 60 PSI Ball control cartridge ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces NSF/ANSI 61 Polished chrome, brushed nickel or oil-rubbed bronze finish Total weight: 3.9 lbs.
  • Página 3: Care And Cleaning

    INSTALLATION INSTRUCTIONS (Continued) Attach one end of each of the water Attach each of the remaining ends of supply lines onto the shanks (11. 1) on the the water supply lines to the hot and faucet body (A), with hot water on the left cold shut-off valves and tighten with a and cold water on the right.
  • Página 4: Replacement Parts

    REPLACEMENT PARTS For replacement parts, call our customer service department at (877) 319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday. PART DESCRIPTION PART # PART # PART # H60K-51D-CH H60K-51D-BN H60K-51D-ORB Handle assembly RP03040CH RP03040BN RP03040ORB Retaining ring RP03041CH...
  • Página 5: Grifo De Cocina Con Rociador Extraíble Grifo De La Cocina

    GRIFO DE COCINA CON ROCIADOR EXTRAÍBLE GRIFO DE LA COCINA H60K-51D-CH - Acabado en cromo pulido H60K-51D-BN - Acabado de níquel cepillado H60K-51D-ORB - Acabado en bronce pulido CONTENIDO DEL PAQUETE Y HARDWARE PARTE DESCRIPCIÓN CANTIDAD Cuerpo del grifo Empaquetadora...
  • Página 6: Especificaciones Del Producto

    ESPECIFICACIONES DEL PRODUCTO Caudal de flujo máximo: 6,8 LPM (1,8 GPM) a 60 PSI Cartucho de control de bola ASME A112.18.1/CSA B125 Fabricado a incluir no más de 0,25 % de contenido de plomo promedio ponderado en superficies mojadas NSF/ANSI 61 Cromo pulido, níquel cepillado y acabado en bronce aceitado Peso total: 1,77 kg INSTRUCCIONES DE INSTALACIÓN...
  • Página 7: Cuidado Y Limpieza

    INSTRUCCIONES DE INSTALACIÓN (continuación) Conecte un extremo de cada una de las Conecte cada uno de los extremos salidas de agua en los vástagos (11. 1) en el restantes de las líneas de entrada de cuerpo del grifo (A), con agua caliente a la agua a las válvulas de cierre de agua izquierda y agua fría a la derecha.
  • Página 8: Dibujo De Instalación

    Para piezas de repuesto, llame a nuestro departamento de servicio al cliente al (877) 319-3757, 7:30 a.m. - 4:30 p.m. CST, Lunes - Viernes. PIEZA DESCRIPCIÓN PIEZA # PIEZA # PIEZA # H60K-51D-CH H60K-51D-BN H60K-51D-ORB Mango de montaje RP03040CH RP03040BN RP03040ORB Anillo de retención...

Este manual también es adecuado para:

H60k-51d-bnH60k-51d-orb

Tabla de contenido