Product Specifications; Installation Instructions - Home2O H60K-51D-CH Manual De Instrucciones

PRODUCT SPECIFICATIONS

Maximum Flow Rate: 1.8 GPM (6.8 LPM) at 60 PSI
ASME A112.18.1/CSA B125
NSF/ANSI 61
Polished chrome, brushed nickel or oil-rubbed bronze finish

INSTALLATION INSTRUCTIONS

1. Shut off the water at the supply valves
under the sink or at the main water
supply. Disconnect the supply lines.
Remove the existing faucet from
the sink.
Clean and dry the surface area where
the new faucet will be mounted.
2. Before installation, remove the quick
connector (2.1) from the end of the
spray hose (2.2) by turning it in a
counterclockwise direction. Loosen the
screws (G) and lock nut (F), and remove
the washer (E).
If installing the faucet with the deckplate,
skip to Step 4.
3. Before installation, ensure the flange (C)
is placed on the bottom of the faucet
body (A). Carefully slide the tubes (3.1)
on the faucet body (A) into the sink
hole. Use caution with the tubes, as they
can crimp or break, causing a leak.
Skip to Step 5.
Optional deckplate installation:
4.
Before installation, remove the flange (H)
from the bottom of the faucet body (A).
Place the deckplate (K) and gasket (B) on
the bottom of the faucet body (A).
5.
Carefully slide the tubes (5.1) on the
faucet body (A) into the center sink
hole and the mounting bolts (C) into the
other holes on the sink. Use caution with
the tubes, as they can crimp or break,
causing a leak. If the sink is uneven, use
silicone under the gasket (B).
1
2
E
F
G
2.1
2.2
3
A
C
3.1
4
A
H
K
B
C
C
4.1
5
A
B
C
C
5.1
Ball control cartridge
Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
Total weight: 3.9 lbs.
6. From underneath the sink, slide the
washer (E) over the tubes (6.1) and
onto the mounting shank (6.2). Thread
the lock nut (F) onto the mounting
shank (6.2). Secure the lock nut (F) into
position by tightening the screws (G).
Do not overtighten.
7. Thread the mounting nuts (D) onto the
mounting bolts (C). Check the position
of the faucet and hand tighten until the
faucet is securely attached to the sink.
NOTE: It is helpful to have a second
person hold the faucet in place while
tightening the mounting nuts (C).
8. From underneath the sink, push the
spray hose (8.1) up through the faucet
body (A) until the end of the hose is
flush with the bottom of the shank (8.2)
on the faucet body (A). Do not allow
the fitting on the bottom of the spray
hose (8.1) to go past the shank. Attach
the pull-out nozzle (J) to the spray hose
(8.1). Feed the spray hose (8.1) down
through the faucet body (A) and through
the hole in the sink surface. Reattach the
quick connector (8.3) by screwing it
onto the threaded end (8.4) of the spray
hose (8.1) in a clockwise direction. Hand
tighten only.
9. Push the quick connector (9.1) on the
end of the spray hose (9.2) into the quick
connect coupling (9.3) on the quick
connect sprayer outlet (9.4). Give the
spray hose (9.2) a tug to ensure the
coupling is connected. If it is necessary to
disconnect the spray hose (9.2) from the
faucet, squeeze the tabs on the side spray
quick connect outlet (9.4) and pull down
on the quick connector (9.1) on the spray
hose (9.2) to disconnect.
10. After connecting the spray hose (10.1),
attach the weight (I) to the spray hose
(10.1) at the location indicated. To attach
the weight (I), use a screwdriver to detach
one side of the weight (I) from the other.
Then connect the two pieces of the
weight (I) back to each other around the
spray hose (10.1).
2
6
6.2
E
F
G
6.1
7
C
D
8
A
J
8.2
8.3
8.4
8.1
9
9.2
9.1
9.3
10
10.1
I
I
Homewerks.com