Descargar Imprimir esta página

Dremel 330 Instrucciones De Funcionamiento Y Seguridad página 3

Publicidad

Idiomas disponibles

Idiomas disponibles

DM 2615302558 8/98
1/11/99 1:47 PM
in the hands of untrained users.
Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools, with
sharp cutting edges are less likely to bind and
are easier to control. Any alteration or
modification is a misuse and may result in a
dangerous condition.
Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the tools operation.
If damaged, have the tool serviced before
using. Many accidents are caused by poorly
maintained
tools.
Develop
maintenance schedule for your tool.
Use only accessories that are recommended
by the manufacturer for your model.
Accessories that may be suitable for one tool,
may become hazardous when used on another
tool.
Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or its
own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and
shock the operator. If cutting into existing walls
or other blind areas where electrical wiring may
exist is unavoidable, disconnect all fuses or
circuit breakers feeding this worksite.
Always make sure the work surface is free
from nails and other foreign objects. Cutting
into a nail can cause the bit and the tool to
jump and damage the bit.
Never hold the workpiece in one hand and
the tool in the other hand when in use.
Never place hands near or below cutting
surface. Clamping the material and guiding the
tool with both hands is safer.
Never lay workpiece on top of hard
surfaces, like concrete, stone, etc...
Protruding cutting bit may cause tool to jump.
Always wear safety goggles and dust mask.
Use only in well ventilated area. Using
personal safety devices and working in safe
environment reduces risk of injury.
After changing the bits or making any
adjustments, make sure the collet nut and
any other adjustment devices are securely
tightened. Loose adjustment device can
unexpectedly shift, causing loss of control,
loose rotating components will be violently
thrown.
Never start the tool when the bit is engaged
in the material. The bit cutting edge may grab
the material causing loss of control of the
cutter. Always hold the tool with two hands
Page 3
Tool service must be performed only by
qualified repair personnel. Service or
maintenance performed by unqualified personnel
could result in a risk of injury. For example:
internal wires may be misplaced or pinched,
safety guard return springs may be improperly
mounted.
When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow
Maintenance Instructions may create a risk of
a
periodic
electric shock or injury. Certain cleaning agents
such as gasoline, carbon tetrachloride, ammonia,
etc. may damage plastic parts.
Safety Rules for Routers
during start-up. The reaction torque of the
motor can cause the tool to twist.
The direction of feeding the bit into the
material is very important and it relates to
the direction of bit rotation. When viewing
the tool from the top, the bit rotates
clockwise. Feed direction of cutting must
be counter-clockwise. NOTE: inside and
outside cuts will require different feed direction,
refer to section on feeding the router. Feeding
the tool in the wrong direction, causes the
cutting edge of the bit to climb out of the work
and pull the tool in the direction of this feed.
Always use the tool with the depth guide
securely attached and positioned flat
against material being cut. The guide
securely positioned on the material improves
the stability and control of your tool.
Never use dull or damaged bits. Sharp bits
must be handled with care. Damaged bits
can snap during use. Dull bits require more
force to push the tool, possibly causing the bit
to break.
Never touch the bit during or immediately
after the use. After use the bit is too hot to be
touched by bare hands.
Never lay the tool down until the motor has
come to a complete standstill. The spinning
bit can grab the surface and pull the tool out of
your control.
Do not use the tool for drilling purposes.
This tool is not intended to be used with drill
bits.
Never use bits that have a cutting diameter
greater than the opening in the base.
-3-
Service

Publicidad

loading