Drill Safety Warnings; Residual Risks; Electrical Safety; Package Contents - DeWalt D21805 Traducido De Las Instrucciones Originales

EnGLIsH
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h ) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

Drill Safety Warnings

Safety Instructions for all Operations
• Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
Use the auxilliary handle(s). Loss of control can cause
•
personal injury.
• Hold the power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
Safety Instructions When Using Long Drill Bits
Never operate at higher speed than the maximum
•
speed rating of the drill bit. At higher speeds, the bit is likely
to bend if allowed to rotate freely without contacting the
workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip
•
in contact with the workpiece. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting the
workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do not
•
apply excessive pressure. Bits can bend causing breakage or
loss of control, resulting in personal injury.
Additional Specific Safety Rules for Drills
Use clamps or other practical way to secure and support
•
the workpiece to a stable platform. Holding the workpiece
by hand or against your body is unstable and may lead to loss
of control.
Wear safety goggles or other eye protection. Drilling
•
operations cause chips to fly. Flying particles can cause
permanent eye damage.
• Bits and tools get hot during operation. Wear gloves when
touching them.
18
Keep handles dry, clean, free from oil and grease. it is
•
recommended to use rubber gloves. This will enable better
control of the tool.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.

Residual Risks

In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D WALT tool is double insulated in accordance
e
with EN62841; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced only by
D WALT or an authorised service organisation.
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Percussion drill
1 Side handle
1 Depth gauge
1 Chuck key
1 Instruction manual
; the
2