Management; Storage; Transport; Dimensions And Weights - DAB K 36/200 Instrucciones Para La Instalación Y El Mantenimiento

Class AM line fuses: indicative values (Amps)
K 36/200 T; K11/500 T; KE 36/200 T;
K 40/200 T; K 18/500 T; K 55/100 T; KE 40/200 T; KE 55/100 T;
K 55/200 T; K 28/500 T; K 66/100 T; K 90/100 T; KE 55/200 T; KE 66/100T; KE 90/100 T;
K 40/400 T; KE 40/400 T;
K 70/300 T; KE 70/300 T;
K 50/400 T; K 30/800 T; K 40/800 T; K 20/1200 T; KE 50/400 T; KE 30/800 T;
KE 40/800 T;
K 25/1200 T; K 70/400 T; K 80/300 T; KE 25/1200 T; KE 70/400 T; KE 80/300 T
K 50/800 T; K 35/1200 T; K 80/400 T; KE 50/800 T; KE 35/1200 T; KE 80/400 T;
- Cable clamp:
PG 13,5
PG 21
The leads of the supply cables must have a rated section no smaller than that illustrated in the following table:
Rated current of the appliance A
> 0,2 and
> 3 and
> 6 and
> 10 and
> 16 and
> 25 and
> 32 and
> 40 and

4. MANAGEMENT

4.1 Storage

All the pumps must be stored indoors, in a dry, vibration-free and dust-free environment, possibly with constant air humidity. They are supplied
in their original packaging and must remain there until the time of installation. If this is not possible, the intake and delivery aperture must be
accurately closed.

4.2 Transport

Avoid subjecting the products to needless jolts or collisions.
To lift and transport the unit, use lifting equipment and the pallet supplied standard (if applicable).
Use suitable hemp or synthetic ropes only if the part can be easily slung, connecting them if possible to the eyebolts provided.
In the case of coupled pumps, the eyebolts provided for lifting one part must not be used to lift the pump-motor assembly.

4.3 Dimensions and weights

The adhesive label on the package indicates the total weight of the electropump. The dimensions are given on page 98.

5. WARNINGS

5.1 Checking motor shaft rotation

Before installing the pump, it is advisable to check that the rotor shaft turns freely. To do this remove the fan cover releasing it from
the groove in the motor end cover, unscrewing the screws and the nuts if provided. Working the fan by hand, turn the rotor shaft a few
times. If this is not possible, dismantle the pump body, slackening the screws to check for any foreign bodies inside it. To reassemble,
proceed in inverse order.
Do not force the fan with pliers or other tools to try to free the pump as this could cause deformation or breakage of
the pump.

5.2 New systems

Before running new systems the valves, pipes, tanks and couplings must be cleaned accurately. Often welding waste, flakes of oxide or
other impurities fall off after only a certain period of time. To prevent them from getting into the pump they must be caught by suitable
filters. The free surface of the filter must have a section at least 3 times larger than the section of the pipe on which the filter is fitted, so
as not to create excessive load losses. We recommend the use of TRUNCATED CONICAL filters made of corrosion-resistant materials
(SEE DIN 4181):
Model
K 36/200 T - K 40/200 T - K 55/200 T - K 11/500 T - K 18/500 T - K 28/500 T - K 55/100 T - K 66/100 T
K 90/100 T - KE 36/200 T - KE 40/200 T - KE 55/200 T - KE 55/100 T - KE 66/100 T - KE 90/100 T
K 40/400 T - K 50/400 T - K 30/800 T - K 40/800 T - K 50/800 T - K 20/1200 T - K 25/1200 T K 35/1200 T 70/300
T - K 80/300 T - K 70/400 T - K 80/400 T - KE 40/400 T - KE 50/400 T - KE 30/800 T - KE 40/800 T - KE 50/800 T -
KE 25/1200 T - KE 35/1200 T - KE 70/300 T - KE 80/300 T - KE 70/400 T - KE 80/400 T
Rated section mm²
≤ 0,2 Flat twin tinsel cord
≤ 3
≤ 6
≤ 10 1,0 (0,75)
≤ 16 1,5 (1,0)
≤ 25
≤ 32
≤ 40
≤ 63
ENGLISH
a.
a
0,5
a
0,75
b
b
2,5 b.
4
6
10
15
Line fuses
3 x 230V 50/60Hz
12
15
20
25
25
40
40
These cables may be used only if their length does
not exceed 2 m between the point in which the cable
or its sheath enters the appliance and its entry in the
plug.
The cables with the sections indicated in brackets
may be used for mobile appliances if their length
does not exceed 2 m.
3 x 400V 50/60Hz
8
8
12
12
16
20
25