Elta 7538N Manual De Instrucciones página 16

01-7538N-GE-EN 7/29/06
(2) Press SEL button hold for more than 2 seconds to turn on TA SEEK/TA ALARM mode. Then press SEL button
shortly and repeatedly to select PI SOUND/PI MUTE, RETUNE L/RETUNE S, MASK DPI/MASK ALL, BEEP
2ND/BEEP ALL/BEEP OFF, SEEK1 /SEEK2 (in RADIO mode), DSP OFF/FLAT/POP M/CLASSICS/ROCK,
LOUD OFF/LOUD ON, SUBW OFF/ON (with subwoofer output), STEREO/MONO (in RADIO mode),
DX/LOCAL (in RADIO mode), VOL LAST/ VOL ADJUST (When it is in VOL ADJUST mode). The next mode
will be A-VOL after VOL ADJUST mode. Then you can adjust the volume level. The minimum value of the
volume level you can set is 10) and ESP10/ESP40 in the sequence and circulation. After selecting the desired
mode, rotate VOL knob to select one setup item of the desired mode.
• TA SEEK/TA ALARM:
• TA SEEK mode: When newly tuned station does not receive TP information for 5 seconds, the radio retunes
to next station which has not the same station (PI) as the last station, but has the TP information.
When TP information gets lost at the current station for retune time which is set by RETUNE SHORT (60
seconds) or RETUNE LONG (90 seconds), the radio start to retune to next same PI station. When same PI
station does not catch in 1 cyclic search, the radio retunes to next station with TP information.
TA ALARM mode: When this mode is selected, any automatic retune mode is not activated. Only double beep
sound (ALARM) is out-put.
When newly tuned station does not have TP information for 5 seconds, beeps come out.
When TP information gets lost at the current station for retune time, the beep sound is out-putted.
When newly tuned station has not RDS signal, PI SEEK is suppressed somewhat.
• PI SOUND/ PI MUTE:
PI SOUND mode: If a car cruises that critical area back and forth, an oscillation phenomenon can be
occurred, because the different PI code can be receive from a same AF. When the different PI sound (DIP)
is heard once in a while, the different PI sound will be heard for less than 1 second.
PI MUTE mode: under above same situation, a mute sound will be heard for less than 1 second.
• RETUNE L / RETUNE S:
The initial time of automatic TA search or PI SEARCH mode is selected.
When PI information is not caught for retune time, the radio start to retune to next same PI station.
When same PI station does not catch 1 cyclic search, the radio goes to last station and waits for 4-5 minute
until PI code is received.
RETUNE L mode: selected as 90 seconds.
RETUNE S mode: selected as 60 seconds.
• MASK DPI/MASK ALL:
MASK DPI mode: masked only the AF which has different PI.
MASK ALL mode: masked the AF which has different PI and NO RDS signal with high field strength.
• BEEP 2 ND /BEEP ALL/BEEP OFF:
BEEP 2 ND mode: the beep is only generated when an allotted double key is pressed long (1 second).
BEEP ALL mode: the beep is generated when every key is pressed (except power and release buttons).
BEEP OFF mode: the beep is disabled.
• SEEK1/SEEK2:
SEEK1: press UP/DOWN button hold to seek up or down for the strong signal station. And then stop seek
when received the strong signal station.
SEEK2: press UP/DOWN button hold to seek up or down for the strong signal station. And do not stop seek
when received the strong signal station. After release it and then received the strong signal station, the seek
will stop.
016.
11:45 AM Page 016