Clip Connection; Operation; Transport; Storage - Kärcher NT 30/1 Ap L Manual De Instrucciones

Removing the dust bag
 The dust bag (special accessories) must always be
removed when vacuuming wet substances.
1. Unlock and remove the suction head.
2. Fold up the dust bag (special accessories).
Illustration G
3. Take off the protective film and close the ventilation
hole with a self-adhesive tab.
4. Close the dust bag (special accessory) tightly with a
cable tie underneath the opening.
5. Take out the dust bag (special accessories).
6. Clean the container inside with a moist cloth.
7. Dispose of the dust bag (special accessory) in ac-
cordance with statutory provisions.
8. Fit and lock the suction head.
Draining the waste water
NT 50/1 only:
1. Drain the waste water via the drain hose.
Illustration H
General
 We recommend not using the "Semi-automatic filter
dedusting" function button when vacuuming wet dirt
with the crevice nozzle or upholstery nozzle (option-
al) when sucking mainly water out of a container.
 The device switches off automatically when the
maximum fluid level is reached.
 When vacuuming non-conductive liquids (e.g. drill
emulsion, oils and grease) the device does not au-
tomatically switch off when the container is full. The
filling level must be continuously monitored and the
container emptied on a timely basis.
 On completion of wet vacuum cleaning: Clean the
main filter element using the filter cleaning. Clean
the electrodes with a brush. Clean the container with
a moist cloth and dry it off.

Clip connection

The suction hose is equipped with a clip system. All ac-
cessory parts with a nominal width of 35 mm can be
connected.
Illustration I

Operation

Switching on the device
1. Connect the mains plug.
2. Switch on the device at the turn switch.
Working with power tools
Only for devices with a built-in socket:
DANGER
Danger of electric shock
Risk of injury and damage.
The socket is only intended for direct connection of pow-
er tools to the vacuum cleaner. Any other use of the
socket is prohibited.
1. Plug the mains plug of the power tool into the power
socket on the vacuum cleaner. The vacuum cleaner
is in Standby mode.
2. Switch on the device at the turn switch.
Note
The vacuum cleaner is automatically switched on and
off with the power tool.
Note
The vacuum cleaner has a startup delay of up to 0.5
seconds and an after-running time of up to 15 seconds.
Note
See the Technical data for the permissible power rating
of the power tool.
3. Remove the angle piece from the suction hose.
Illustration J
4. Install the tool adapter on the suction hose.
5. Connect the tool adapter to the power tool.
Illustration K
Semi-automatic filter dedusting
Note
Actuating the filter dedusting every 5-10 minutes ex-
tends the working time of the main filter element.
Note
The semi-automatic filter dedusting can only be
switched on when the device is switched on.
1. Press the semi-automatic filter dedusting button 5x.
The main filter element is then cleaned by a blast of
air (pulsing sound).
2. Power dedusting (for particularly severe contamina-
tion of the main filter element): Close off the suction
pipe or angle piece with your hand and press the
semi-automatic filter dedusting button 5x with the
device switched on.
Illustration L
Switching off the device
1. Press the semi-automatic filter dedusting button 5x.
2. Switch off the device at the turn switch.
3. Pull out the mains plug.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Folding the push handle in/out
NT 50/1 only:
1. Release the push handle lock and adjust the push
handle.
Storing the device
1. Store the suction hose and mains cable as shown in
the illustration.
Illustration M
2. Store the device in a dry room and secure it against
unauthorised use.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Remove the suction hose with floor nozzle from the
support. Carry the device by the carrying handle and
the suction pipe, not by the push handle.
2. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.
English

Transport

Storage

15