Tabla de contenido
Publicidad
GB
TECHNICAL DATA
max. 150W (0101R)
• O
:
utput
max. 500W (0501R)
• V
:
230V~, 50H
Oltage
• p
:
ip44
rOtectiOn
class
A
• r
:
eplacement
illuminant
Rt
R7S
A
Rt
IllumInant InstallatIon
• Loosen the screw on the top of the floodlight and swing the lens forward.
• Remove the illuminant from the packaging.
• Avoid touching it with bare hands since this causes grease stains which lead to
overheating. Use a clean, dry, lint-free cloth.
• Insert one end of the illuminant into the socket, press against it, and insert
the other end of the illuminant into the socket. Ensure that the socket is not
damaged.
• Then close the lens and retighten the screw.
INSTALLING
Installation may only be carried out by trained professionals according to the
applicable installation regulations. Contact a licensed electrician.
ATTENTION!! Before installation, the power supply must be disconnected and
locked out.
• Loosen the screws on the side of the housing and remove the mounting brackets.
• Install the mounting brackets to a suitable surface – always follow the installation
location requirements listed under "General Safety Information" (s. 1-4).
• Reattach the floodlight housing to the mounting brackets but do not tighten the
screws fully.
• Loosen the screws on the back of the junction box and remove the cover.
• Remove the cable guide screw connection and guide it over the connecting cable
– the screw connection thread must face in the direction of the cable end.
• Loosen the cable grip screws and remove the cable grip.
• Guide the screw connection seal over the cable as well, and then insert the cable
into the junction box. Ensure the seal is seated in the cable guide correctly – if the
connecting cable is too thin, the cable guide must be additionally sealed.
• Connect the wires according to Figure 5/Figure 6.
• Tighten the cable guide screw connection, install the cable grip, and tighten the
screws.
• Install the junction box cover and tighten the screws.
SETTING THE FLOODLIGHT DIRECTION
• Loosen the screws on the sides of the mounting brackets, adjust the floodlight
direction, and then retighten all screws.
8
z
.-N
. 0599940555/120W
R
.-N
. 0599950555/400W
R
REPLACING THE ILLUMINANT
You can find the technical data for the illuminant under "Technical Date" or on the
type plate attached to the floodlight housing.
• Disconnect and lock out the power supply to the floodlight. Allow the floodlight to
cool down sufficiently!
• Loosen the screw for the lens on top of the floodlight and swing the lens forward.
• Remove the illuminant from the packaging.
• Avoid touching it with bare hands since this causes grease stains which lead to
overheating. Use a clean, dry, lint-free cloth.
• Insert one end of the illuminant into the socket, press against it, and insert
the other end of the illuminant into the socket. Ensure that the socket is not
damaged.
• Then close the lens and retighten the screw.
CLEANING
• Disconnect and lock out the power supply to the floodlight. Allow the floodlight to
cool down sufficiently!
• Clean with a dry or slightly moist, clean, lint-free cloth and a mild detergent if
required. Do not use cleaners that contain abrasives or solvents.
• If required, the illuminant can be cleaned with a lint-free cloth moistened with
ethyl alcohol. ATTENTION! After cleaning the illuminant with ethyl alcohol, it must
be allowed to air dry for at least 20 minutes.
MAINTENANCE
• If the lens is damaged it must be replaced immediately.
• Clean any dirt from the housing or the lens
immediately, since it could cause overheating.
WARRANTY
During manufacturing this REV product is passed through several quality testing
stations which are set up with newest technology. Should nevertheless a defect
arise, REV offers a warranty to the following extent:
1. The duration of the warranty is 24 months after the date of purchase.
2. The unit is either repaired or replaced by REV free of charge or if it can
be shown that it has become unusable during the warranty period due to
a manufacturing or material defect.
3. The liability does not cover transport damages or damaged incurred
through defective installation.
4. If REV repudiates the warranty claim and no objection is made within 6
months, the right to repair becomes time-barred.
5. In a warranty case the unit must be sent to the dealer or REV together with
the sales slip and a short description of the defect.
6. If there is no proof for a warranty liability being in place, any repair carried
out will be invoiced. ethyl alcohol. ATTENTION! After cleaning the
illuminant with ethyl alcohol, it must be allowed to air dry for at least
20 minutes.
GB
9
Publicidad
Tabla de contenido
