Electrical Connection; First Start-Up - Sammic GLASS-PRO GP Serie Manual Del Usuario

Installation
4) Check the following values of the feed water flow rate:
Water flow rate Minimum value
All models
5) [Models without drain pump]
outer diameter of 30 mm to the drain line [Fig. 1/A]. For the
maximum drain height, observe the following values:
Drain height
Models with drain pump
Modelos sin bomba de vaciado
2.3 Unpacking
⚠ Wa r n ing
Risk of trapping hands
There is a high risk of trapping your hands if you lift the ma-
chine onto the base and place it on the ground.
– To move the machine from one place to another, hold the
machine from the sides.
1) Remove the packaging that protects the machine.
2) Lower the machine from the pallet on which it is mounted.
2.4 Assembly
⚠ Wa r n ing
Risk of serious accidents if the machine cannot be
disconnected or turned off
– When installing the machine, make sure the operator will be able
to reach the switch and plug without difficulty.
Notice
Risk of water leakage
– Before installation, turn off the water stopcock.
1) Screw the legs to the base of the machine.
2) Adjust the height of the legs so that the machine is stable and
level with the ground.
3) Place the machine at the installation site.
4) Check that the tap water pressure is within the parameters
specified in the previous chapter (use of the pressure gauge).
Notice
Risk of hose clogging and/or choking
– Avoid making reductions with the hose when installing.
5) Connect the water outlet hose to the drain point.
6) Connect the water supply hose to the mains water point.
User's manual — 2900450/0
15 L/min
Connect the drain pipe with an
Maximum value
800 mm
100 mm
⚠ C au t io n
Risk of irritation due to chemical exchange and foam
release
If you insert the detergent and rinse aid inlet hoses into the
wrong bottles, the machine will produce excessive foam.
– Pay attention to the labelling on the chemical hoses before
inserting the hoses into the corresponding bottles.
7) Insert the detergent and rinse aid inlet hoses into the corre-
sponding bottles.
2.5

Electrical connection

⚠ C au t io n
Electric shock hazard
– The machine must be connected to earth.
– The machine has an external earth-connection screw
with the symbol shown;
ℹ Information
The connections may only be accessed by qualified personnel
▶
[ Installation qualification p. 13 ],
1) Before plugging in the machine, make sure that the mains volt-
age matches the voltage indicated on the machine nameplate.
2)
Set up the machine's electrical connections, depending on the
model and configuration of the machine.
3) Disconnect the electrical power supply: unplug the circuit-
breaker on the electrical panel corresponding to the external
power supply socket of the machine.
4) Make the electrical connection according to the type of model
and electrical configuration of your machine, as explained in the
attached document "Electrical diagram" for each case.
5) Prepare a residual current circuit-breaker with a sensitivity of
30 mA and a magneto-thermal circuit-breaker as described in
the following table:
Model Voltage
3 x 2.5 mm 2
GP-35 230V/50Hz/1~
220V/60Hz/1~
3 x 2.5 mm 2
GP-40 230V/50Hz/1~
220V/60Hz/1~
3 x 2.5 mm 2
GP-50 230V/50Hz/1~
220V/60Hz/1~
2.6

First start-up

1) Turn on the water stopcock.
2)
Switch on the circuit-breaker of the electrical panel correspond-
ing to the external power supply socket of the machine.
3) Place the overflow pipe in position
4) Check that the filters are correctly fitted. [Fig. 3]
Cable sec- Total Protection
tion Power
2,58 kW 16 A 2P
2,75 kW 16 A 2P
3.35 kW 16 A 2P
EN
15