Initial Settings; Temperature Settings; Preparation For Operation - Sammic GLASS-PRO GP Serie Manual Del Usuario

NombreProducto | Operation
5) Turn on the machine.
2.7 General machine settings
2.7.1

Initial Settings

Temperature settings

1) To enter the temperature settings section, when turning on the
machine, press and hold the PROG button
seconds while the program is loading.
2) Press the START button
– Tank temperature settings
– Boiler temperature settings
Tank temperature settings (washing)
1) The icon lights up and one of the program/cycle icons
flashes. Each symbol represents a tank temperature as shown
in the following table:
Icon flashes Tank temperature
Disconnection of elements (room
temperature)
50 °C
60 °C60 °C
65 °C
2) To select the tank temperature, press the PROG button
⇒
After 3 seconds without pressing the PROG button
temperature is selected and the cycle led stops flashing.
3) To confirm the machine, press the ON/OFF button.
⇒
The machine shuts down.
Boiler temperature settings (rinsing)
1) The icon lights up and one of the program/cycle icons
flashes. Each symbol represents a tank temperature as shown
in the following table:
Icon flashes Boiler temperature
Disconnection of elements (room
temperature)
75 °C
80 °C
85 °C
2) To select the tank temperature, press the PROG button
⇒
After 3 seconds without pressing the PROG button
temperature is selected and the cycle led stops flashing.
3) To confirm the machine, press the ON/OFF button.
⇒
The machine shuts down.
Thermal lock
If the thermal lock function is activated:
•
If you press the START button
16
in the first two
to choose between the icons:
(washing).
(rinsing).
.
, the
.
, the
, the cycle cannot advance.
• The icon lights up when the boiler has not yet reached the
setpoint temperature at the time of rinsing. The wash pump
continues to run until the boiler reaches its pre-set temperature.
To activate the Thermal lockfunction:
1)
Switch the appliance on by pressing the ON/OFF button.
2) To activate this function, access the electronic board and set
switch 1 to position 1. See the SW1 position last figure in the
appendix at the end of the manual.
2.7.2 Auto start settings
The "Automatic Start" option allows the machine to start the wash-
ing cycle automatically when close the door.
To enable/disable the "auto start" option:
1) With the door open, press the START key
⇒
Icon on: auto start enabled.
⇒
Icon auto start disabled.
off:
2.7.3 Model settings
If the electronic board is changed or de-configured, the machine
requires the model to be adjusted by means of the following adjust-
ment section:
1) To access the electronic board, turn off the machine: press the
ON/OFF button.
2) To activate this function, access the control board and set
switches 2-5 to position 1 or position 0 as shown in the table
below. See the SW1 position last figure in the appendix at the
end of the manual.
No. SW-2 SW-3 SW-4
1-2 0 0 0
3-4 1 0 0
9-10 0 0 1
11-12 1 0 1
3 Operation
⚠ W a rn in g
Risk of serious injury due to operation when the
machine is faulty
Using the machine when it is faulty or in poor condition can af-
fect personal safety and damage the machine.
– If you detect any fault or anomaly in the machine, contact an
authorised service agent immediately.
3.1

Preparation for operation

1) Before turning on the machine, check the level of
detergent and rinse aid in the bottles.
2) Open the door and verify that all components are
in good condition and correctly installed:
– Filters.
– Overflow.
– Washing arms (upper and lower).
.
SW-5 Model Drain pump
0 GP-35/40 NO
0 GP-35/40 B YES
0 GP-50 NO
0 GP-50/B YES
User's manual — 2900450/0