Technical Data; Safety Recommendations - YATO YT-17205 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 29

TECHNICAL DATA

Index
YT-17205
YT-17207
YT-17213
DESCRIPTION OF THE MACHINE
The hydraulic lift has been designed to be used for tasks implying lifting signifi cant weights. It must not be used as a permanent
support element. It is also unacceptable to use the lift to transport lifted loads. The device has been designed exclusively for
domestic use and must not be used professionally, namely in plants and for lucrative purposes. A correct, reliable and safe func-
tioning of the device depends on its adequate operation, so:
Before you commence work with the tool, read the operating manual thoroughly and keep it for future reference.
The supplier shall not be held responsible for any damage and injuries caused due to using the tool for purposes it has not been
designed for, failure to observe safety recommendations and the recommendations indicated within this manual. Using the device
for tasks which do not comply with the purpose it has been designed for shall also cancel the guarantee rights the user is entitled to.

SAFETY RECOMMENDATIONS

The lift is a hydraulic device working under signifi cant loads. During work it is required to observe basic safety principles.
Before you start work, read the operating manual and keep it for future reference.
Do not ever exceed the maximum load of the lift.
It is prohibited to use the device to lift people and animals.
The lift has been designed exclusively for the purpose of lifting, and must not be used for other purposes. It is required to use
additional safety devices (e.g. racks) to support the lifted object, before work under it may commence.
In case of lifting vehicles it is necessary to block or wedge the wheels and engage the safety brake.
Do not leave a lifted load unattended. Do net permit children and those who have not been trained in operation of the device to
enter the working area.
Do not wear loose clothes and jewellery. Gather long hair.
Use personal protection means.
The lift must be placed on an even, fl at, hard and stable surface.
The lift must be placed upon the device to be lifted so that the load is supported in the middle section of the saddle.
It is absolutely prohibited to adjust the safety valve.
Keep the device far from sources of heat and fl ames, since they might damage the device or impair its functioning.
Before you proceed to lifting any load whatsoever, make sure that once the load has been lifted, the lift will not shift.
Before you proceed to lifting any load whatsoever, male sure the lift is not damaged in any way. If the lift requires repair, have it
repaired by an authorised workshop.
Be prudent and do not work when you are tired or under infl uence of medicines.
Do not modify any elements of the lift, which may have impact on the compliance of the lift with the standard indicated in the
declaration of compliance.
Have the device repaired exclusively in authorised service points, using solely original spare parts, so as to ensure the required
level of safety during work.
ASSEMBLY AND OPERATION
The jack is supplied as a pre-assembled system and does not require assembly or adjustment.
Before you start the operation, make sure that the release valve is loosened and perform some 6 full pumping cycles to ensure
proper distribution of hydraulic oil.
It is necessary to check and tighten all screw connections before each use. This will increase the safety of use and extend the
service life of the jack. The jack comes with wheels to facilitate moving the jack on fl at surfaces. To do this, grip the jack arm and
simply move the device in the desired direction. If you need to move the jack in vertical direction, use the front wheel axle of the
jack and the base section of the hydraulic cylinder as handles.
Lifting
Before you start lifting make sure that the jack and the load being lifted are within the operator's sight when making all movements.
Join both parts of the lifting arm and secure with the catch (II), then insert the jack arm into the socket and tighten the valve (III) to
O R I G I N A L
8
GB
Lifting capacity [tons]
2,5
2,5
3,0
I N S T R U C T I O N S
Lifting range [mm]
100 - 465
85 - 520
145 - 500
Weight [kg]
26,2
34,0
37,0

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Yt-17207Yt-17213

Tabla de contenido