Product Description; Technical Data; Safety Instructions - YATO YT-55600 Manual Del Usuario

PRODUCT DESCRIPTION

The Transmission Jack is a hydraulic jack designed for lifting and lowering a gearbox and other heavy car components, directly
from underneath the vehicle. The height of the jack enables easier and safer dismounting and mounting of the gearbox. The jack
must not be used as a permanent support. Proper, reliable and safe operation of the equipment depends on appropriate use, that
is why you should
Read and keep the entire manual before the fi rst use of the tool.
The supplier shall not be held liable for any damage or injury resulting from improper use of the tool, failure to observe the safety
regulations and instructions of this manual. Use of the equipment for purposes other than those for which it was intended shall
cause the loss of the user's rights to the warranty.

TECHNICAL DATA

Index No.
YT-55600

SAFETY INSTRUCTIONS

The jack is a heavy duty hydraulic device. The basic safety principles must be observed during work.
Read and keep the instruction manual before beginning work.
Never exceed the maximum load of the jack. The car parts to be raised and lowered must not protrude too far beyond the saddle
of the jack. If the centre of gravity of the load is excessively misaligned with the jack saddle it rests on, this may cause instability
or fall and lead to serious injuries.
It is forbidden to lift people or animals with the jack.
The jack is designed only for lifting or lowering the gearbox or other car components like live axle and suspension components.
Other applications are not allowed. The use of the jack as a lift trolley for moving cars, a spreader or permanent support is pro-
hibited. Before you use the jack, ensure the car is at a suffi cient height to allow the jack to be easily slid underneath the chassis,
lower the component to be dismounted, and then move the jack with its load away from underneath the car. It is forbidden to move
the car when using the jack.
The jack with its load may only be moved around if the jack saddle is in the lowest position. During moving the jack around use
extreme caution. Ensure the fl oor is solid, even and clean along path for the jack. Ensure the fl oor is able to withstand the weight
of the jack with a load placed on it. Move the jack about in slow and smooth movements. Avoid jerking and moving it too fast. Do
not move the jack up or down a slope.
Using the jack as a base for permanent load support is not allowed. Once the jack with its load is moved away from a car, carry
the load to a base support, work table or other fi xed support using an engine crane, for example.
Do not leave the load on the jack saddle unattended. Do not allow children or people who are not trained in the operation of the
equipment to stand in the jack operation or storage areas.
Do not wear loose clothing or jewellery. Long hair should be tied up.
Wear personal protective equipment.
The jack must be placed on a level, fl at, hard and stable surface.
Ensure the jack is loaded in such a way as to position the centre of gravity of the load above the centre of the saddle.
Adjusting the safety valve is strictly forbidden.
Keep the equipment away from heat sources and fi re as this may damage the device or impair its operation.
Before lifting any load, make sure that there is no movement of the jack after lifting.
Before lifting any load, make sure that the jack is not damaged in any way. If the jack needs to be repaired, contact the manufac-
turer's authorised repair garage.
Be sensible, do not work when tired or under the infl uence of medication or narcotics.
Do not make any modifi cations to the parts of the jack which may aff ect the conformity of the jack to the standard mentioned in
the declaration of conformity.
Have the product repaired in authorised workshops only and using only original spare parts. This will ensure proper safety of
operation.
ASSEMBLY AND OPERATION
Assembly of the jack
The jack must be assembled before use.
Use bolts (II) to fasten the wheel arms to the jack base. Put a spring washer under each bolt head.
O R I G I N A L
8
GB
Lifting capacity [kg]
500
I N S T R U C T I O N S
Lifting range [mm]
1140 - 1945
Weight [kg]
24