Domyos T900A Manual Del Usuario página 24

TROUBLESHOOTING
The treadmill will not turn on:
Check that the power cord is plugged into a wall socket in working condition (to check if the wall socket is working, plug in a lamp or other electrical device to check).
Check that the power cord is plugged into a wall socket that is properly grounded. If you need an extension lead, use only a 3-core, 2,5 mm² (14 gauge) cable that is no longer than 1.5 m
(5 ft).
Check that the power cord is fully inserted in the back of the treadmill.
After connecting the power cord, make sure that the key is inserted into the console.
Check the switch on the frame of the treadmill near the power cord, it must be in the «I» position.
The running belt slows down when walked on:
If you need an extension lead, use only a 3-core, 2,5 mm² cable that is no longer than 1.5 m. Do not use a power strip.
If the running belt is too tight, the performance of the treadmill may decrease and the running belt may become damaged.
Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn the running belt centring and tensioning screws anticlockwise a quarter turn. When the running belt is properly
tightened, you should be able to lift each edge of the running belt 2 to 3 cm above the deck. Ensure the running belt remains centred. Then, plug in the power cord, insert the safety key
and run the treadmill for a few minutes.
The treadmill makes a noise:
Rubbing noise:
Check that the running belt is properly centred (the belt must not rub against the sides).
Grinding noise:
Check, and if necessary, tighten all the external parts of the running belt.
The running belt is no longer centred:
Locate the colour indicators on the back of your treadmill.
If you see red, the belt needs to be re-centred. This helps protect the running belt and avoids unexpected shutdowns.
Run your treadmill at 4km/h (2.5 mph) and stand at the back of the machine.
ERROR CODES
E1, E2, E4, E5, E6, E8, E10, E11, E12, E13, E14, E15, E16: Contact the after-sales service (see the last page of your user manual).
E3 Check that none of the parts are impeding the movement of the belt. If the problem persists, contact the after-sales service.
E7 Have your electricity supply checked by a professional then contact the after-sales service.
E9 Unfold your treadmill. If the problem persists, contact the after-sales service.
E17 Turn off your treadmill and then turn it on again. If the problem persists, contact the after-sales service.
COMMERCIAL WARRANTY
DOMYOS guarantees this product (parts and labour), under normal conditions of use and from the date of purchase (date indicated on the receipt), for:
Lifetime for the welded metal structure of the treadmill
2 years for all parts and labour
DOMYOS's obligation with regard to this warranty is limited to the replacement or repair of the product, at the discretion of DOMYOS.
This guarantee doesn't apply in cases of:
Damage caused during transportation
Poor assembly
Misuse or abnormal use
Poor maintenance
Repairs made by technicians not approved by DOMYOS
Use in excess of 5 hours per week
This warranty does not cancel the legal warranty applicable in the country of purchase.
To take advantage of your product warranty, consult the table at the end of the user's guide.
24
The belt is offset to the left:
Turn the left adjustment screw clockwise a half turn.
The belt is offset to the right:
Turn the right adjustment screw clockwise a half turn.
Leave your treadmill running until the belt repositions itself (1-2 minutes) and repeat the operation if
necessary. However, be careful not to overtighten the belt.
The running belt stops while running
The running belt is a wearing part that becomes loose over time. Re-tighten it as soon it begins to slip
(sliding sensation, jerks in speed).
Turn the 2 adjustment screw clockwise a half turn.Repeat the operation if necessary, but be careful
not to overtighten the belt. The belt is properly tightened if you can lift the edges 2 to 3 cm on each
side