Publicidad
Idiomas disponibles
Idiomas disponibles
Wall Mounting on the Wall
Select a location away from electrical cables, pipes or other items that could
cause a hazard when inserting screws in the wall.
CAUTION: Ensure the wall is capable of supporting the weight of the phone.
For additional security, it is recommended that you mount the phone on a
plywood backboard. Mitel is not responsible for phones damaged as a result
of improper wall mounting.
Insert two mounting screws 3 1/4 inches (8.25 cm) apart. Allow about 3/16
of an inch (0.5 cm) between the wall and screw heads for mounting the
phone. Use #10 screws 1 to 1.5 inches (2.5 to 4 cm) in length for mounting
screws and anchoring devices suitable for the wall.
Follow the procedure for mounting the phone on the wall plate to complete
the installation.
Removing and Reinstalling the Lens (See Figure
The 5212/5224 IP Phone is shipped with the plastic lens and a fixed designation
card installed. An installer can change the fixed designation card by removing
the lens.
To install a fixed designation card and reinstall the lens:
Remove the screw that holds the option module on the back of the phone.
Keep the screw in a safe place—you must use the same screw in step
Lift the lower edge of the option module until you feel the inner tabs release,
and then gently lift the upper edge of the module.
NOTE:
Always lift the lower edge of the module first, otherwise you may damage the
module and/or the lens.
Remove the lens by lifting the upper edge, then sliding the lower edge down.
Place the appropriate fixed designation card on the face of the phone.
Slide the tabs of the lens into the underside of the phone.
Snap the lens tightly into place by applying pressure to both the middle and
top of the lens. Secure the option module using the screw from step
NOTE:
For troubleshooting information, refer to the appropriate Mitel ICP Technical Doc-
umentation.
4
Notice to Canadian Customers
This Class B digital apparatus complies with Canadian ICES-003.
Notice to U.S. Customers
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
D
)
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE:
Changes or modifications not expressly approved by Mitel Networks™ Corpora-
tion may void the user's right to operate the equipment.
.
The handset provided with this equipment is hearing aid compatible.
This equipment is not for connection to the telephone network or public coin
phone service. It is only for use when connected to Mitel systems.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING
TEST CALLS TO EMERGENCY NUMBERS
• Remain on the line and briefly explain to the dispatcher the reason for the
call.
• Perform tests during off-peak hours such as early morning or late
evenings.
Notice to Customers in EU Countries
.
We, Mitel Networks Ltd.
Of, Mitel Business Park
Portskewett
Monmouthshire
NP26 5YR
UK
Declare that for the hereinafter mentioned product the presumption of
conformity with the applicable essential requirements of
DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT (RTTE DIRECTIVE) AND OF THE COUNCIL
Any unauthorized modification of the product voids this Declaration.
For a copy of the original signed Declaration of Conformity (in full conformance
with EN45014), please contact the Regulatory Approvals Manager at the above
address.
is given.
Mitel \ 5212 IP Phone \ 5224 IP Phone
Publicidad
