Publicidad
Idiomas disponibles
Idiomas disponibles
7. THE SIDE SPACERS AND THE TUB SUPPORT BAR
1.
Inside the tank a special adhesive label shows the load limit of the display cabinet. Adhering to this
reference ensures maximum performance from the display cabinet and perfect product storage.
2.
Position the bar by laying it on the two supports.
4.
Exceeding the load limit will damage both the product and the display cabinet. . Insert the side
spacers according to the type of tub used, resting them on the front and rear supports.
A)
Spacer
B)
Support bar
8. CONNECTION TO THE MAINS
1.
Ensure that mains voltage and frequency are the same as those stated on the rating plate
to the appliance.
Ensure that the supply socket has the following characteristics:
2.
b)
earthed.
It fulfils the requirements of the rated current as set out on the rating plate.
the IEC regulations:- Magnetothermal differential switch with In = nominal value as stated on the rating
plate; - Differential with Id sensitivity = 30 mA.
room.
4.
The connecting cable to the appliance is
any other environment, it will be necessary to change the cable with the appropriate type (for example
H07 VVF for external use).
in a horizontal position or has been turned upside down, leave for at least three hours in the correct
position before switching on the power supply.
reduction adapters) (see figure 5).
9. CONTROLS
The control unit is supplied with standard setting.
2. Setting.
If no alarms are active, the word
"set"
key once more; the value will appear on the display, to change it use the
Description of controls:
1.
6.
Fnc (exit function)
7.
Set (See figure 6).
10. CHECKING CORRECT OPERATION
CHECK THAT: 1
. The plug is connected.
3.
The thermometer shows the desired temperature for the goods to be stored.
5.
The flap is closed properly.
lamps.
7.
The room temperature does not exceed that in which the appliance is designed to work
normally, i.e. +30°C, 55% r.h. (climatic class 4).
grille, to ensure an adequate flow of air to the motor compartment.
11. INTERNAL CLEANING (EVERY 15 DAYS)
1.
Switch off the appliance.
dampened in warm water and use a neutral detergent; wipe dry with a soft cloth.
use inflammable or abrasive products or water jets to clean the display cabinet.
12. REPLACING THE INTERNAL LIGHTS
1.
Switch off the appliance.
seat using light pressure and a flat-headed screwdriver.
of place.
4.
Remove the lamp.
figure 7)
Operator's guide
3.
C)
Tub support bar
D)
Load limit (see figure 4).
3.
Ensure that there is no risk of explosion (AD) in the
H05 VVF
N.B.
If during transport or storage the appliance has been placed by mistake
5.
Insert the plug (do not use three-way adapters and
1. To set the temperature
"set"
appears. To view the
Control unit
2.
Lighting button.
2.
The refrigeration unit switch is switched on (green light on).
6.
The appliance is not exposed to direct sunlight or to high-powered
8.
There is a clearance of at least 30 cm in front of the
2.
Remove the refrigerated goods.
2.
To replace the lamp, remove the front guard. In particular remove it from its
5.
Replace the fluorescent tube and refit all parts in reverse order (see
7
Position the tub, and spacers where needed.
, designed for internal use. For installation in
press the
SETPOINT
"Up"
3.
Glass cabinet ON switch
4.
3.
Clean the tank and panes with a sponge
3.
Turn the fluorescent tube 90° until it snaps out
5
(A)
attached
)
It is properly
a
c)
It complies with
"set"
key.
value, press the
and
"Down"
keys.
4.
Up
5.
Down.
The internal light is on.
ATTENTION 4. NEVER
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO
Publicidad
