Preparation For Operation - VERTO 52G055 Manual De Instrucciones

GB
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
BLADE SAWING MACHINE (JIGSAW)
52G055
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
SAFETY RULES FOR LASER DEVICE
• Use dust-masks when cutting to protect your respiratory system
against produced dust.
• Carefully check the processed material before cutting to eliminate
possibility of cutting nails, bolts, or other hard objects.
• Do not cut pipes with the jigsaw.
• Do not cut objects thicker than allowed in technical specification
for a given material.
• Prior to operation check if there is enough space under processed
material to avoid table or floor damage with the blade.
• Hold the jigsaw in closed hand.
• Ensure the jigsaw does not have contact with the material before
pressing the switch.
• Do not touch moving parts with your hand.
• Before cutting floor, wall or other material ensure it does not
contain conductors.
• Do not put away the jigsaw until it stops moving. Do not switch the
jigsaw on when not holding it.
• To remove the blade switch the jigsaw off with the switch and wait until
the blade stops moving. Then disconnect the tool from mains socket.
• Do not touch the blade or processed material immediately after
finishing the work. Those elements may be hot and cause burns.
• When you see unusual behaviour of the tool or hear strange noises,
immediately switch off the tool and remove the plug from mains
socket.
• To ensure proper cooling keep ventilation holes in the jigsaw body
uncovered.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of operational injuries.
CONSTRUCTION AND USE
Jigsaw is a hand-operated power tool with insulation class II. It is
driven by a single-phase commutator motor.
The tool is designed for making straight, coarse cuts, curved cuts and
holes in wood, wood-like materials, plastics and metals (provided that
appropriate blade is used). Range of use covers repair and building works,
and any work from the scope of individual, amateur activities (tinkering).
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Wheel for rotational speed control
2. Switch
3. Switch lock button
4. Adaptor
5. Dust extraction outlet
6. Switch for pendulum action setting
7. Footplate
8. Guiding roller
9. Edge guide locking screws
10. Blade protection
11. Guard
12. Blade holder
* Differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Blade
2. Edge guide
3. Dust extraction adaptor
4. Hexagonal key

PREPARATION FOR OPERATION

BLADE INSTALLATION
• Set the switch for pendulum action (6) to position "III" and lift the
guard (11) (fig. A).
• Use the hexagonal key to loosen fixing screws (a) of the blade (12)
(fig. B).
• Slide blade to the blade holder (12) to mechanical stop (blade teeth
should face forward).
• Important! Make sure the blade is properly positioned in the
guiding roller (8).
• Tighten previously loosened fixing screws (a) of the blade and
ensure the blade is properly fixed.
• Blade removal is similar to installation, only the sequence of actions
is reversed.
Use blades suitable for T-shank holder mechanism, as shown on fig. C.
DUST EXTRACTION
To improve dust extraction from processed material surface, the
jigsaw is equipped with own dust blow-off system, which cleans the
surface being cut. Additionally, it is possible to attach external dust
extraction system to the adaptor. Dust blow-off and extraction system
is more efficient when the guard is lowered.
• Slide adaptor (4) into the dust extraction outlet (5) and turn
counter-clockwise to secure (fig. D).
• Attach suction hose of the dust extraction system to the adaptor (4).
Make sure the connection is tight.
INSTALLATION OF GUIDE FOR PARALLEL CUTTING
Guide for parallel cutting may be installed on either left or right side
of the jigsaw footplate.
• Loosen the edge guide locking screws (9).
• Slide the edge guide bar into holes in the footplate (7), use the
scale to set required distance and fix by tightening the edge guide
locking screws (9) (fig. E).
Edge guide bar should be pointed downwards.
9
- 1 pce
- 1 pce
- 1 pce
- 1 pce