Operation Of The Device - Sthor 78873 Manual De Instrucciones

GB

OPERATION OF THE DEVICE

Preparing for operation
Check the vacuum container, if it is necessary empty the waste.
Check the condition of filters. In the case of soiling clean filters only by dry method with a jet of compressed air, of pressure of not
more than 0.3 MPa. If dirt cannot be removed from the filter, replace them with a new ones. Check the gasket integrated with the
upper edge of the filter, if the it shows damage, the filter must be replaced for a new one.
NOTE! It is prohibited to work with a vacuum cleaner without properly mounted air filter. This can lead to damage of the vacuum
cleaner and electric shock.
It is possible to install wheels for the base of the vacuum cleaner. To do this, press the pins of small wheels into the holes of the
base and enter the handles of large wheels axis into the slots of the base (II).
The metal chain was fixed to the underside of the container (III). Make sure that during the work it will have contact with the
ground, it let to dissipate static electricity, which builds-up during operation.
The vacuum cleaner is equipped with a float (IV), which shuts off the air every time the tank will overflow. Before you start the
operation, make sure that the float and guides, on which it moves, are not damaged, that they are clean and they guarantee the
free movement of the float. Each float activation is indicated by a louder engine running and a decrease in suction power.
Note! It is prohibited to use the vacuum cleaner without the operational float.
Set the cloth filter in the container so as to seal the entire circumference adjacent to the edge of the tank (V).
Mount the cover on the upper edge of the tank of vacuum cleaner so it adheres by its entire circumference. Using clips push the
lid into the tank. Pay attention to the fact that on the cover there are two designated place, which allow you to obtain the best
sealing of this connection (VI).
Connect elastic hose to the inlet. The hose connection must be inserted in the hole, so that the notches on it match the protrusions
of the inlet, and then turn it in the direction of the arrow with inscription "LOCK" (VII). Make sure that the hose cannot slip out of
the hole during operation.
Connect to free end of hose the telescopic tube by sliding it (VIII). The telescopic tube allows to adjust the length, for this purpose
slide and hold the lock, which is located on the tube and adjust the length of the pipe (IX). Releasing the lock button will lock the
selected length of the pipe. Make sure that the lock worked and pipe length will not change spontaneously during operation. At the
opposite end of telescopic tube attach the ending, sliding it like a pipe. Select the ending appropriate for the type of work. Wide
ending is designed to clean large and flat surfaces and the narrow ending is for hard to reach places, which are not accessible
for the wide ending.
In order to dismantle the interior, turn its connection in the direction of the arrow described with inscription "LOOSE" and then pull
out connection from the inlet. Dismantling extension tubes and endings must be carried out inversely to their installation.
Vacuum cleaner also allows for hose connection to the outlet, which make possible to used it as a blower. The hose is connected
to the connection by pushing the socket (X).
The base of the vacuum cleaner is equipped with handles allowing for temporary mounting of equipment, for its use during the op-
erating time or for storage of vacuum cleaner. Extension tubes and suction nozzles (XIII) can be attached in the base handles.
Operation of the vacuum cleaner
NOTE! It is prohibited to work with a vacuum cleaner with hot ash. Temperature of the sucked waste by the vacuum cleaner may
not exceed 40 °C.
Make sure that all the preparatory activities have been properly performed.
Make sure that the vacuum switch is on the off position "O".
Plug the power cord into the mains socket, and then set the switch on position "I" (XI).
On the tubes extension connection there is a valve (XII), which opening of reduces the vacuum created by the vacuum cleaner.
Reduction of the vacuum may be necessary when cleaning unfixed carpets or floor coverings. When cleaning the surface of the
water or wet dirt, close this valve.
After finishing work switch off the vacuum cleaner and then unplug the power cord from the wall socket. Proceed to the mainte-
nance activities for vacuum cleaner.
Built-in mains socket
The vacuum cleaner has a built-in mains socket that is used to supply power to electric tools. This makes it easier to use the
vacuum cleaner as the installation withdrawing the dust generated during operation. Voltage appears in the socket when you con-
nect the cleaner power plug into a mains socket. Therefore, before connecting the appliance to the mains, and the electric tools
O R I G I N A L I N S T R U C T I O N S
11