Device Operation - Sthor 82954 Manual De Instrucciones

Do not place the appliance near any heat or fi re sources.
Connect the appliance only to the power network with the voltage
and frequency indicated on the nameplate of the appliance.
The plug of the power cord must match the power socket. Do not
modify the plug. Do not use any adapters to fi t the plug to the socket.
If unmodifi ed, the plug matches the socket thus reducing the risk of
an electric shock.
After each application, unplug the power cord plug from the socket.
The appliance is intended for indoor use only. Do not expose the ap-
pliance to any precipitation or moisture. If water and moisture enters
the appliance, the risk of an electric shock is signifi cantly increased.
Do not immerse the product in water or any other liquid.
Do not obstruct the ventilation openings and make sure they are
clear. Obstructed and/or clogged ventilation openings may cause
the appliance to overheat. This can lead to damage to the appliance
or cause fi re or electric shock.
Do not overload the power cord. Do not use the power cord to carry,
connect, or disconnect the plug from the power socket. Avoid any
contact between the power cord and heat sources, oil, sharp edges,
and moving parts. Damage to the power cord increases the risk of
an electric shock. If the power cord is damaged (e.g. it is cut or
its insulation is melted), immediately unplug it from the wall sock-
et and return it to an authorised service facility. It is not allowed to
use the product with a damaged power cord. It is not allowed to
have the power cord repaired. It must be changed for a new one
at an authorized service centre. When using extension cords, use
extension cords with power parameters such as those shown on the
appliance's nameplate.
If you notice any damage to any part of the appliance, you must
discontinue using it. In this case, the appliance must be taken to an
authorised service centre or replaced by yourself, if this is permitted
by the user's manual.
Turn off the appliance and unplug the power cord from the wall sock-
et before you start any work on replacing, cleaning, or adjusting.
Switch off the appliance before replacing the accessories and un-
plug the power cord from the socket.
This appliance may be used by children of at least 8 years of age
and by persons with reduced physical, mental abilities and persons
with no experience or knowledge of the appliance, if supervised or
instructed on its safe use so that the risks associated with it were
understandable. Children should not play with the appliance. Unat-
tended children should not be allowed to perform the cleaning and
maintenance of the device.
The vacuum cleaner is designed for dry running. It is forbidden to
draw in water, wet ash or other wet waste. This may result in electric
shock, which may endanger the health and life of the user and others.
Never draw in hot, glowing or burning objects. This can lead to fi re
or explosion and expose the user to serious injury or death. The
maximum temperature of suctioned waste must not exceed 40 ° C.
The device is intended for use in closed rooms and should not be
O R I G I N A L
GB
exposed to water, including precipitation.
Make sure that the mains power parameters comply with the ones
shown on the appliance's nameplate before connecting the power
cord plug to the unit.
Before each use, check the condition of the appliance, including the
power cord and plug. If any faults are noticed, do not use the device.
Damaged cables and wires must be replaced with new ones in a
specialist workshop.
Make sure that the power cord plug has been disconnected from the
mains socket before carrying out maintenance on the unit.
Keep the device out of reach of unauthorized persons, especially
children. Make sure that the device is out of the reach of unauthor-
ized persons, especially children also during operation.
Move the device using the handle, do not move the device by pulling
the power cord.
Check the condition of the fl exible hose at regular intervals. Never
use the vacuum cleaner if its fl exible hose is damaged.

DEVICE OPERATION

CAUTION! Turn off the appliance and unplug the power cord from
the socket during all equipment assembly and disassembly activities.
Appliance assembly and disassembly
Take the vacuum cleaner, the dust container and accessories out
of the packaging and remove all packaging components. Install the
dust container.
Before fi rst use, make sure that the container has all components
and is correctly assembled.
If the container is mounted on a vacuum cleaner, it must be re-
moved. Push the latch button with your fi nger and then remove the
container from the vacuum cleaner (II).
Remove the fi lter from the dust container. The fi lter has a fl ange,
the shape of which is adapted to the shape of the dust container.
A fl exible gasket is mounted around the fl ange to prevent dirt from
entering the vacuum cleaner drive from the container. Check the
condition of the gasket, replace the entire fi lter with a new one if any
damage is noticed.
Slide the fi lter into the dust container so that the fl ange rests on the
guides inside the container (III). At the edge of the fl ange, there is a
gap, into which one of the guides (IV) should be inserted. A correctly
installed fi lter is supported by a fl ange against all guides and one of
the guides has been inserted into the fl ange gap.
Mount the container with the fi lter to the vacuum cleaner housing.
The lower edge of the container should rest on the vacuum cleaner
housing (V), then press, hold down the locking button and snap the
container into place on the housing.
Caution! If excessive force is required to latch the container, check
that the fi lter is installed correctly. Forceful latching of the container
may damage the vacuum cleaner and cause incorrect operation.
I N S T R U C T I O N S
11