Device Operation - Sthor 82953 Manual De Instrucciones

specialist workshop.
Make sure that the power cord plug has been disconnected from the
mains socket before carrying out maintenance on the unit.
Keep the device out of reach of unauthorized persons, especially
children. Make sure that the device is out of the reach of unauthor-
ized persons, especially children also during operation.
Move the device using the handle, do not move the device by pulling
the power cord.
Check the condition of the fl exible hose at regular intervals. Never
use the vacuum cleaner if its fl exible hose is damaged.

DEVICE OPERATION

CAUTION! Turn off the appliance and unplug the power cord from
the socket during all equipment assembly and disassembly activities.
Appliance assembly and disassembly
Take the vacuum cleaner, the dust container and accessories out
of the packaging and remove all packaging components. Install the
dust container.
Before fi rst use, make sure that the container has all components
and is correctly assembled.
If the container is mounted on a vacuum cleaner, it must be re-
moved. Push the latch button with your fi nger and then remove the
container from the vacuum cleaner (II).
Remove the fi lter from the dust container. The fi lter has a fl ange,
the shape of which is adapted to the shape of the dust container.
A fl exible gasket is mounted around the fl ange to prevent dirt from
entering the vacuum cleaner drive from the container. Check the
condition of the gasket, replace the entire fi lter with a new one if any
damage is noticed.
Slide the fi lter into the dust container so that the fl ange rests on the
guides inside the container (III). At the edge of the fl ange, there is a
gap, into which one of the guides (IV) should be inserted. A correctly
installed fi lter is supported by a fl ange against all guides and one of
the guides has been inserted into the fl ange gap.
Mount the container with the fi lter to the vacuum cleaner housing.
The lower edge of the container should rest on the vacuum cleaner
housing (V), then press, hold down the locking button and snap the
container into place on the housing.
Caution! If excessive force is required to latch the container, check
that the fi lter is installed correctly. Forceful latching of the container
may damage the vacuum cleaner and cause incorrect operation.
The container installed correctly is fl ush with the housing at its entire
edge, the housing tongue fi ts in the lower opening near the edge
of the container and the locking button fi ts in the upper opening of
the container (VI). A correctly installed container cannot be removed
otherwise than by pushing back the lock button.
O R I G I N A L
GB
Installation of accessories (VII)
Slide one of the attachments or a fl exible hose into the opening at
the front of the dust container. It is permissible to vacuum soft sur-
faces, e.g. carpets, upholstery, etc. without an installed attachment
or hose.
The fl exible hose joint without the embossed part is designed to be
inserted into the opening of the dust container and the joint with the
embossed part should be inserted over the tip.
The brush attachment is used to clean surfaces that can be easily
scratched. The narrow tip attachment is used to clean hard-to-reach
areas.
If the unit is used as a compressor, attach the pumping hose to the
air outlet. Lift the hose joint lever, slide the joint onto the air outlet
valve and then lower the joint lever (X).
The free hose connection should be fi xed to the valve of the product
to be pumped in the same way as described above.
Preparing for operation
Check the vacuum cleaner tank, empty it of waste, if necessary.
Check the fi lter. If the fi lter is dirty, dry clean with a compressed
air stream of no more than 0.3 MPa or wet under a stream of run-
ning, lukewarm water. Do not clean the fi lter in dishwashers or with
a high-pressure water jet. If dirt cannot be removed from the fi lter,
replace it with a new one. Check the condition of the fi lter seals,
replace the fi lter with a new one if they show damage.
CAUTION! It is forbidden to work with a vacuum cleaner without a
properly installed air fi lter. This can cause damage to the vacuum
cleaner as well as electric shock.
Working with a vacuum cleaner
CAUTION! It is forbidden to use a vacuum cleaner to vacuum hot
ashes. The temperature of waste suctioned by the vacuum cleaner
must not exceed 40 degrees Celsius. C.
Make sure that all preparatory work has been carried out correctly.
Make sure that the vacuum cleaner switch is in the "O/OFF" position
(VIII).
Insert the plug of the power cord into the mains socket on the plug,
the LED will light up and the lamp in the upper housing of the vacu-
um cleaner will light up.
Slide the switch forward to use the appliance as a vacuum cleaner or
backward to use the appliance as a compressor (VIII).
To check the pressure, stop the pumping by moving the switch to
the O/OFF position, and then read the pressure indicator display. Al-
ways turn off the compressor to read the pressure inside the pumped
product.
After fi nishing work, turn off the vacuum cleaner using the on/off
switch, and then unplug the power cord from the mains socket. Start
I N S T R U C T I O N S
11