Angle Grinder; Intended Use; Before Use - Defort DAG-600-B Instrucciones De Servicio

GB

Angle grinder

INTENDED USE

This tool is intended for grinding, cutting and deburr-
ing metal and stone materials without the use of water;
with the appropriate accessories the tool can also be
used for brushing and sanding
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1. Spindle
2. Clamping fl ange
3. Spanner
4. Spindle-lock button
5. Auxiliary handle
6. Safety guard
7. Mounting fl ange
8. On/off locking switch
SAFETY
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fi re and/or serious injury.
● Only use this tool for dry grinding/cutting
● Only use the fl anges which are supplied with this
tool
● This tool should not be used by people under the
age of 16 years
● Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
● Use the original SBM Group accessories which can
be obtained from your SBM Group dealer
● For mounting/using non- SBM Group accessories
observe the instructions of the manufacturer con-
cerned
● Use only accessories with an allowable speed
matching at least the highest no-load speed of the
tool
● Do not use damaged, deformed or vibrating grind-
ing/ cutting discs
● Handle and store grinding/cutting discs carefully to
avoid chipping and cracking
● Protect accessories from impact, shock and grease
● Do not use a grinding/cutting disc that is larger than
the maximum recommended size
● Only use grinding/cutting discs with a hole diameter
which fi ts mounting fl ange (7) without play; never use
reducers or adaptors to fi t large-hole grinding/cut-
ting discs
● Never use grinding/cutting discs with a threaded
hole, of which the thread is not long enough to ac-
cept the spindle length of the tool
● Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
6
1
2
OUTDOOR USE
● Connect the tool via a fault current (FI) circuit break-
er with a triggering current of 30 mA maximum
● Only use an extension cord which is intended for
outdoor use and equipped with a splashproof cou-
pling-socket

BEFORE USE

● Before using the tool for the fi rst time, it is recom-
mended to receive practical information
● Do not work materials containing asbestos (asbes-
tos is considered carcinogenic)
● Take protective measures when during work dust
can develop that is harmful to one's health, combus-
tible or explosive (some dusts are considered carci-
nogenic); wear a dust mask and work with dust/chip
extraction when connectable
● Be careful of hidden electrical wires or gas- and wa-
ter pipes; check the work area, for instance with a
metal detector
● Be careful when cutting grooves, especially in sup-
porting walls (slots in supporting walls are subject to
country- specifi c regulations; these regulations are
to be observed under all circumstances)
● Clamp the workpiece in case it does not remain
stationa ry from its own weight
● Do not clamp the tool in a vice
● Use completely unrolled and safe extension cords
with a capacity of 16 Amps (UK 13 Amps)
● Wear protective glasses and gloves, hearing protec-
tion and sturdy shoes; when necessary, also wear
an apron
● Always mount auxiliary handle (5) and protective
guard (6); never use the tool without them
● Be sure tool is switched off when plugging in
DURING USE
● Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
● If the cord is damaged or cut through while working,
do not touch the cord, but immediately disconnect
the plug; never use the tool with a damaged cord
● Push spindle-lock button (4) only when spindle (1) is
at a standstill
● Keep hands away from rotating accessories
● When grinding metal, sparks are generated; keep
other persons and combustible material from work
area
● In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the
plug
● In case the cutting disc is blocked, resulting in jerk-
ing forces on the tool, immediately switch off the
tool
● In case of current interruption or when the plug is
accidentally pulled out, unlock the on/off switch (8)
immediately and put it in the OFF-position in order to
prevent uncontrolled restarting
● Do not apply so much pressure on the tool that it
comes to a standstill