System Description; Electrical Voltage - SSS Siedle DCIP 740-01 Manual De Instrucciones

English

1 System description

DoorCom IP
Siedle DoorCom IP links the Siedle
world of building communication to
the IP world.
Door calls are transformed via the
DoorCom IP and transmitted via the
IP network to certain PCs. If video
cameras are fitted at the door sta-
tion, the picture of the visitor is addi-
tionally transmitted. The DoorCom
IP Software Client is used here as a
virtual in-house telephone for com-
munication to the door station.
The Software Client must be ins-
talled on every PC in the network
which is intended to receive a door
call.
Assignment of door calls to the
Software Clients takes place using
an IWA address (Interface Working
Address) which is entered in the
DoorCom IP with the aid of the con-
figuration software.
DCIP 740‑...
The DoorCom IP 740-... serves as
an interface between a Siedle Multi
system and an IP network.
The DoorCom IP is able to display
the picture on the PC monitor in
conjunction with the Siedle Software
Client and at the same time hold the
door call via the PC.
The door call can optionally also
be held over the telephone system
using a telephone, while the picture
is displayed by the Software Client
and all control functions such as
door release can also be initiated by
the software. For this, a DCA 740-01
must additionally be connected to
the DoorCom IP. The video camera
picture continues to appear in the
Software Client on the PC monitor.
2 Safety remarks
System requirements

Electrical voltage

Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician. Failure to observe this
regulation could result in the risk of
serious damage to health or fatal
injury due to electric shocks.
• When working at the device,
observe the remarks relating to
mains cut-off.
• Observe the standard DIN
EN 60065!
• When establishing the electronic
connection, observe the require-
ments of VDE 0805 /EN 60950.
• The building installation must
include an all-pole mains switch
with a contact separation of at least
3 mm.
• Ensure maximum fusing of 16 A
for the mains connection in the
building installation.
• When planning, the required
distributor space for switch panel
mounted devices must be taken into
account.
• External voltages >30 V AC/DC
must not be injected into the
inhouse telephones.
Devices with 230 V connection
In accordance with DIN VDE 0100
Part 410, Section 411.1.3 ensure
that the DoorCom installation and
the mains voltage are securely iso-
lated. The sheathing of the connec-
tion cable (safety extra-low voltage)
should only be stripped back far
enough to ensure that reliable con-
nection is possible.
For mains connection and network
settings such as assignment of the IP
address, the responsible network
administrator must be consulted.
Find out about the necessary safety
measures and system requirements
before starting installation and com-
missioning of the DoorCom IP.
System requirements for configu‑
ration software DCIP CO 600‑0
• PC with Intel Pentium III from
1 GHz or comparable processor
• at least 512 MB RAM
• min. 25 MB hard disk memory
• USB port or serial port depending
on which PRI 602-... is being used
• CD-ROM drive for installation
• VGA graphics card with at least
1024 x 768 pixel
• Operating system Windows 7
32/64 Bit
• Admin rights for installation
Additional memory capacity is
required for:
• Acrobat Reader 7
• Microsoft Internet Explorer from
version 6
System requirements for the
Software Client
• Windows 7 SP1 (32 Bit, 64 Bit in
32 Bit emulation mode),
.Net framework 3.5,
• Windows 8 .Net framework 3.5,
• min. Intel Pentium Dual Core,
3.0 GHz, 2 GB RAM, 100 Mbps
Ethernet,
• Graphic Cards (min 1024x768, full
DirectX 9 support, min. 128 MB
VRAM),
• Microsoft® DirectX® 9.0c,
• Sound card, headset
Speech quality
The audio quality (speech transmis-
sion) is highly dependent on the
quality of the audio components
built into the PC (headset, handset
and sound card).
3