Restoring Factory Defaults; Maintaining; Troubleshooting; Remote Control - Dynex DX-LCD32-09 Guia Del Usuario

Maintaining

To delete the RRT information:
1 Press MENU. The on-screen menu opens.
2 Press or to select Lock, then press . The password entry
screen opens.
Picture Sound
Enter Password
Select
3 Press the number buttons to enter the password. The default
password is 0000. The Lock menu opens.
Picture Sound
Change Password
System Lock
US
Canada
RRT Setting
Reset RRT
Select
4 If necessary, press or to select System Lock, then press
or to select On.
5 Press or to select Reset RRT, then press ENTER.
6 When a message asks if you want to clear the RRT Setting, select
Yes to delete the RRT rating information, or select No to exit
without deleting the information.

Restoring factory defaults

You can restore all settings to the factory defaults. When you restore
settings, all customized settings are cleared, except the parental control
password and the parental lock settings. After you restore settings, your
TV needs to memorize channels again.
To restore factory defaults:
1 Press MENU. The on-screen menu opens.
2 Press or to select Setup, then press to open the Setup
menu.
Picture Sound
Menu Language
Transparency
Zoom Mode
Noise Reduction
Advanced
Closed Caption
XVS
Restore Default
Select
3 Press or to select Restore Default, then press or
ENTER.
Time Setup Lock Channel
– – – –
Move
Exit
MENU
Time Setup Lock Channel
On
Move
Exit
MENU
Time Setup Lock Channel
English
Off
Wide
Weak
Off
Move
Exit
MENU
4 When a message asks if you want to restore factory settings,
select Yes to restore the settings, or select No to exit without
restoring settings.
Maintaining
To clean your TV:
1 Turn off and unplug your TV.
2 Wipe it with a soft, dry cloth.
If the surfaces are extremely dirty, dampen a soft cloth with a
soap and water solution or a weak detergent solution.
Use eyeglass cleaner to remove stubborn dirt from the screen.
Cautions: Never use alcohol, paint thinner, or benzine to clean your TV.
Before using a chemically treated cloth, read the instructions that
came with the cloth.

Troubleshooting

Caution: Never try to repair your TV yourself. Refer all servicing to
qualified service personnel.
Note: If the problem is not solved after you try the solutions in this
section, turn off your TV, then turn it back on again.

Remote control

Problem
Remote control does not
work.

Video and audio

Problem
No picture (screen not lit)
and no sound.
Dark, poor, or no picture
(screen lit) but good sound.
No color, incorrect color, or
dark picture.
Only snow and noise
appear on the screen.
Dotted lines or stripes.
Double images.
Good picture but no sound.
Audio noise.
Solution
• Make sure that the power cord is
plugged into a power outlet.
• Make sure that the batteries are
installed correctly. Align the + and
– symbols on the batteries with
the + and – symbols in the battery
compartment.
• Replace the batteries.
Solution
• Make sure that the power cord is
plugged into a power outlet.
• Press on the remote control or
the side of your TV.
• Try another channel.
• Adjust the brightness.
• Select a different picture mode.
• Make sure that the antenna or
cable TV cables are connected
securely.
• Adjust the Color (color saturation)
on the Picture menu.
• Try another channel.
• Make sure that the antenna or
cable TV cables are connected
securely.
• Adjust the antenna.
• Move your TV away from sources
of interference such as cars, neon
signs, or hair dryers.
• Adjust the antenna. You may
need a high-directional outdoor
antenna.
• Press MUTE to make sure that the
sound is not muted.
• Make sure that the sound mode is
set to Stereo or Mono.
• Move devices that use IR
(infrared) away from your TV.
19