Ryobi RC18118C Manual Del Usuario página 11

Traducción de las instrucciones originales
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 20
Safety, performance, and dependability have been given
top priority in the design of your charger.
INTENDED USE
This charger is only intended to charge RYOBI ONE+
battery packs listed in this manual.
The product is only for use in cars.
The product is not intended to charge any other type of
battery or be used as a power supply or any other purpose.
environments.
CHARGER SAFETY WARNINGS
Please read and observe these instructions before using the
product. Failure to follow these instructions and warnings
increases the risk of electric shock, fire and explosion.
WARNING
Do not recharge primary cells (non-rechargeable).
WARNING
Mains voltage must correspond with the voltage
Before using the product, check that the product
enclosure, cable and adaptor plug are not damaged.
If damage is found, do not use and follow instruction in
the maintenance section of this manual.
The product must not be damp, and should never be
used in a damp environment.
The product is for indoor use only.
Do not use the product if it has suffered any heavy
shock or jolting, or is damaged in any other way.
Do not conduct charging in a position which may
become exposed to sunlight or other heat source.
Recommended temperature range at charging vicinity
is 10° to 25° C.
Due to the heat generated during charging, the product
should not be operated on a combustible surface.
Do not conduct charging operations in the vicinity
of flammable materials. Example: Cloth, packaging
materials, paint, spray paint or aerosols, lubricant,
thinners, petrol containers, gas containers or gas
appliances.
Do not cover any ventilating slots and provide adequate
ventilation during operation.
Never modify, disassemble or attempt to repair the
product yourself.
Do not allow the charger or batteries to become
contaminated with any material which could be
conductive. Example: Metal particles from grinding,
cutting or machining processes.
Remove the adaptor of the product from the receptacle
when it is not in use or when cleaning it.
Only use extension cable that is approved and in good
condition.
Protect battery contacts to avoid a short circuit caused
by metallic objects which could cause a fire or explosion!
Do not charge batteries which show signs they have
leaked electrolyte. Dispose of them properly.
Never charge a damaged battery pack. If damaged,
replace immediately.
If the battery is not going to be used for a while, remove
the adaptor from the receptacle and take the battery off
the product.
Always place the product on a rigid surface, not a car
seat, while charging battery pack. Do not place anything
such as a jacket over the product while it is in use.
Charge in a well ventilated area. Do not block charger
vents. Keep them clear to allow proper ventilation.
If at any point during the charging process none of the
LEDs are lit, remove the battery pack from the charger
to avoid damaging the product. Do not insert another
battery. Return the charger and battery to your nearest
service center for service or replacement.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
damage due to a short circuit, never immerse your
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking.Check with the forwarding company for further
advice.
KNOW YOUR PRODUCT
See page 83.
1. Green LED
2. Red LED
3. Battery port
4. 12V adaptor
5. Key hole hanger
MAINTENANCE
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Remove the adaptor from the receptacle when it is not
in use or when cleaning it.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English |
1

Publicidad

Tabla de contenido
loading

Tabla de contenido