Fender MUSTANG I Manual Del Proprietário página 11

♫
For example, if you only want the middle third of the
pedal range to register with the amplifier, only move
the EXP-1 pedal back and forth through the middle
third of its range of motion. You must start the calibra-
tion process with the EXP-1 pedal positioned some-
where within the desired range.
5.
Turn the DATA WHEEL to select a new preset.
6.
The EXP-1 expression pedal has been calibrated!
♫
Repeat the calibration procedure each time you
change EXP-1 pedals, plug the EXP-1 into a different
amplifier, or perform a Factory Restore proceedure
(see page 13) on the amplifier.
EXP-1 Pedal Settings
The EXP-1 pedals settings can be saved with the current pre-
set so that each time you select a particular preset, the EXP-1
functions are customized for that preset. Before you change
the EXP-1 settings, select the preset that you want to save
the EXP-1 settings with.
To configure EXP-1 settings:
1.
Plug the EXP-1 pedal into the 4 BUTTON FOOTSWITCH
jack on the back of your Mustang amplifier using the
included cable.
2.
Select the preset with which you want to use the EXP-1.
3.
Press and hold the DATA WHEEL until the Expression
Mode Enable menu appears.
4. Rotate the DATA WHEEL to change the settings in the
current menu. Press the DATA WHEEL to select the next
menu from the list below.
♫
SHORTCUT: You can speed select menus in either direc-
tion by rotating the DATA WHEEL while holding it down.
5.
Save the current preset if you want to keep the modified
EXP-1 settings, otherwise, press EXIT, then select a differ-
ent preset using the DATA WHEEL to erase your changes.
EXP-1 Menus:
• Expression Mode Enable — (Off, Amp, Stomp, Mod,
Delay, Reverb, Volume) Select the category that you want to
control with the EXP-1 in Expression mode, or select "Off" if
you want the pedal to be OFF in Expression mode.
♫
You must have an effect selected for the current preset
on the amplifier (or in Fender FUSE) to make that cat-
egory of effect become available for selection in this
menu.
• Expression Mode Parameter — (Variable) Select the
parameter that you want to control with the EXP-1 in
MUSTANG I I I /I V/V ( V. 2)
™
f e n d e r . c o m
Expression mode. Your options will vary depending on the
category you selected in the Expression Mode Enable menu
above, and the effect module that is selected in the current
preset.
• Expression Mode Heel/Toe — (Variable) Use these two
menus to set the level of the active parameter (selected
in the menu above) with the heel of the pedal in the fully
down position (Heel Setting) and with the toe of the pedal
in the fully down position (Toe Setting). Range options will
vary depending on your selection in the Expression Mode
Parameter menu above.
• Expression Mode Type — (Capture, Live) If "Live" is
selected, the current pedal position will override the stored
preset setting for the assigned expression pedal parameter
when a preset is first selected. If "Capture" is selected, the
pedal is disabled until you move the pedal after a preset is
first selected.
• Expression Effect Bypass — (On/Off) Select "On"
to bypass (turn off) the effect currently selected in the
Expression Mode Enable menu when switching the EXP-1 to
Volume mode. Select "Off" to leave the effect active (keep
on).
• Expression Parameter Restore — (On/Off) Select "On"
to return the Expression Mode Parameter to the stored pre-
set value when switching the EXP-1 to Volume mode. Select
"Off" if you want the parameter to be left set to the position
of the pedal (toe position) when switching to Volume mode.
• Volume Mode Behavior — (Volume/Off) Select "Volume"
if you want the pedal to control the master volume in
Volume mode. Select "Off" if you want the pedal to be OFF
when switched to Volume mode.
• Volume Mode Heel/Toe — (0–100%) Use these two
menus to set the master volume level with the heel of the
pedal in the fully down position (Heel Volume) and with the
toe of the pedal in the fully down position (Toe Volume).
• Pedal Initial Source — (From Preset/From Pedal) Select
"From Preset" if you want the EXP-1 mode to switch to the
Preset Default mode (see note below) each time you select a
preset. Select "From Pedal" if you want the EXP-1 to remain
in whichever mode the EXP-1 is currently in as you change
presets. The Pedal Initial Source setting is a global setting.
It is not associated with any preset and does not need to be
saved; it stays set to the current selection.
♫
Preset Default mode is the mode (volume or expression)
that the EXP-1 is in when you save the preset. You can
change the Preset Default mode by re-saving the preset
with the EXP-1 in a different mode, or using Fender
FUSE software.
11