Protecting The Environment - Black+Decker BDCR18 Manual De Instrucciones

ENGLISH
When cutting thin sheet metal, clamp a piece of scrap
u
wood to the back surface of the workpiece and cut through
this sandwich.
Spread a film of oil along the intended line of cut.
u
Pocket cutting in wood (fig. I)
Measure and mark the required pocket cut.
u
Fit a saw blade suitable for pocket cutting.
u
Rest the shoe (3) on the workpiece in such a position that
u
the blade forms an appropriate angle for the pocket cut.
Switch on the tool and slowly feed the blade into the
u
workpiece. Make sure that the shoe (3) remains in contact
with the workpiece at all times.
Cutting branches
Branches up to 25 mm in diameter can be cut with this tool.
Warning! Do not use the tool while in a tree, on a ladder or
on any other unstable surface. Be aware of where the branch
will fall.
Cut downward and away from your body.
u
Make the cut close to the main branch or tree body.
u
Vertical cutting
The tool allows close cutting to corners and other difficult
areas.
Insert the shank of the saw blade into the blade holder
u
with the teeth of the blade facing upward.
Hold the tool with the shoe (3) facing downward so that
u
you are as close to the work surface as possible.
Cut forward and away from your body.
u
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Blades
The saw will accept a blade up to 30 cm long. Always use the
shortest blade suitable for your project but long enough to
keep the blade cutting through the material. Longer blades are
more likely to be bent or damaged during use. During opera-
tion some longer blades may vibrate or shake if the saw is not
kept in contact with the workpiece.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
8
(Original instructions)
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com
Technical data
Input voltage
No-load speed
Stroke length
Weight
Charger
Input voltage
Output voltage
Current
Approx. charge time
Hours
Battery (where BL2018*
supplied)
Voltage V
DC
Capacity Ah
Type Li-Ion
Level of sound pressure according to EN 60745:
Sound pressure (L ) 79.5 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 90.5 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 60745:
2
Cutting boards (a ) 17.9 m/s , uncertainty (K) 1.5 m/s
h,B
Cutting wooden beams (a ) 19.7 m/s
h, WB
BDCR18 (H1)
V 18
DC
-1
Min 0-3000
mm 22
kg 1.5
905902**/ 905998**/
N4940** 906349**
V 100-240 220-240
AC
V 8-20 8-20
DC
A 400 1000
3-11 1.5-5
BL1518* BL2518* BL4018
18 18 18
2.0 1.5 2.5
Li-Ion Li-Ion
2
2 2
, uncertainty (K) 1.5 m/s
18
4.0
Li-Ion