Troubleshooting; Protecting The Environment - Black+Decker BDCCS18 Traducción De Las Instrucciones Originales

Work with the shoe pressed against the workpiece.
u
Hints for optimum use
As some splintering along the line of cut on the top side of
u
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
Where splintering is to be minimized, e.g. when cutting
u
laminates, clamp a piece of plywood onto the top of the
workpiece.
Pocket cutting (fig. K)
Warning! Never tie the blade guard in a raised position. Never
move the saw backwards when pocket cutting. This may
cause the unit to raise up off the work surface which could
cause injury.
A pocket cut is one that is made when the edge of the material
does not push the lower guard open, but the bottom edge of
the rotating blade cuts into the middle of the material.
Adjust the shoe (5) so the blade cuts at desired depth.
u
Tilt the saw forward and rest front of the shoe on material
u
to be cut.
Using the retracting lever, retract lower blade guard to
u
an upward position. Lower rear of shoe until blade teeth
almost touch cutting line.
Release the blade guard (its contact with the work will
u
keep it in position to open freely as you start the cut).
Remove hand from guard lever and firmly grip secondary
u
handle (7), as shown in figure N. Position your body and
arm to allow you to resist kickback if it occurs.
Make sure blade is not in contact with cutting surface
u
before starting saw.
Start the motor, allow saw to come to full speed, and then
u
gradually lower the saw until its shoe rests flat on the
material to be cut. Advance saw along the cutting line until
cut is completed as shown in figure K.
Release trigger and allow blade to stop completely before
u
withdrawing the blade from the material.
When starting each new cut, repeat as above.
u

Troubleshooting

Problem Possible Cause
Unit will not Battery pack not
start.
installed properly.
Battery pack not
charged.
Motor stops
Battery pack not
while mowing. inserted into charger.
Charger not plugged in. Plug charger into a working out-
Surrounding air
temperature too hot or
too cold.
Possible Solution
Check battery pack installation.
Check battery pack charging
requirements.
Insert battery pack into charger
until LED appears.
let. Refer to "Important Charging
Notes" for more details.
Move charger and battery to a
surrounding air teperature of
above 40 degrees F (4.5°C) or
below 105 degrees F (+40.5°C).
(Original instructions)
Problem Possible Cause
Unit shuts off
Battery pack has
abruptly. reached its. maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted).
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool using a
u
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com
ENGLISH
Possible Solution
Allow battery pack to cool down.
Place on charger and allow to
charge.
11