Philips HB 580 Manual De Instrucciones página 7

Remote control (fig. 21)
a
Time setting button 0-30 minutes
b
Start button
c
Pause button
d
Blinking signal
e
Pilot lamp
f
Buzzer
g
Display
• Note that in the following instructions, the buttons to be
used are shown in red.
• In the following cases the number 00 will appear on the
display:
- After you have put the plug in the wall socket;
- At the end of a tanning session;
- After a power failure.
In all these cases, the tanning lamps are out.
- When you put the plug in the wall socket, pilot light
(fig. 22). This pilot light will stay on as long as the appliance is
connected to the mains. Fully unwind the mains cord.
- First set the time of the tanning session. Push the
the time forward; push the
(fig. 23). Keep the button pressed in to adjust the time more
quickly.
- Switch on the tanning lamps by pressing the start button
(fig. 24).
d
• A blinking signal will appear; the set time is shown on display
(25 minutes in this case) (fig. 25). The countdown of the set
tanning time will now start.
• You can interrupt the tanning session by pressing pause button
(fig. 26). The tanning lamps will be switched off. You can switch
them back on again by pressing start button
The remaining tanning time will appear on the display.
• You can shorten the set tanning time by first pressing the start
I
button (fig. 28). The tanning lamps are switched off. Set the new
tanning time by means of button
- The HPA lamp of the facial tanner will not start burning right away,
but will only go on after about 3 minutes.
- During the last minute of the session the buzzer will sound
(fig. 29). During this minute, the pause function does not work.
• As soon as the set tanning time has elapsed, the solarium will
switch off automatically.
Use
- Push the canopy backward so that you can lie down on the couch
(fig. 30). When you lie on the couch, pull the canopy back into
horizontal position.
• NB: when the solarium has not been used for some time, the
hinges of the canopy may squeak when you push the canopy
backward and forward the first time.
- Switch the appliance on by setting the required tanning time on the
remote control (see section 'Remote control').
• For the correct tanning times, see the section 'UV tanning sessions:
How often? And how long?'
- Switch the body cooler on by means of the switch (fig. 31) and
select the required setting and power (n or b) (fig. 32).
- If you like, you can also switch on the facial tanner (fig. 31). Select
setting , for 75% of its full power or » for full power (fig. 33).
- Don't forget to put on the protective goggles provided.
e
+ button to put
- button to put the time backward
I
(fig. 27).
a
and press start button I.
Cleaning
• Always unplug the solarium and let it cool down before
you start cleaning it.
• You can clean the outside of the solarium with a damp cloth.
Be careful not to let any water run into the appliance.
• Do not use any scouring agents or scouring pads.
• Never use abrasive liquids like alcohol, methylated spirits,
petrol or acetone to clean the acrylic sheets: this could
cause irreparable damage.
Hour counter
The hour counter indicates the number of hours the lamps have
been on. You can read the counter by removing the end cover at
the head of the couch. See section on 'Replacing lamps and/or
starters' for instructions on how to remove the end cover.
will go on Replacing lamps and/or starters
After some time (after a few years in case of normal use) the light
emitted by the tanning lamps will become less bright. When this
happens, you will notice a decrease in the tanning capacity of the
solarium. You can overcome this problem by setting a slightly longer
tanning time or by replacing the lamps or by having them replaced.
• You can have the tube lamps and/or starters replaced by an
I
authorised Philips Service Centre. They have the knowledge and
skills required for this job and the original spare parts for your
solarium.
g
• If you want to replace the tube lamps and/or starters yourself, you
should proceed as follows:
- Unplug the appliance.
fi
- Remove the decorative caps and undo the screws of the end cover
at the head of the couch and remove them (fig. 34).
- Pull the acrylic sheet approx. 10 cm out of the appliance.
- Undo the snap strip on the rear side of the couch, starting at the
head (figs. 35 to 36).
- Do the same with the snap strip on the front side of the couch.
- Remove the acrylic sheet (fig. 37).
Now you can replace the tube lamps and starters.
• NB: You can now also clean the acrylic sheet, if you wish.
- To remove the lamps, turn them to the left or to the right so that
you can lift them out of their holders.
f
- The lamps and/or starters of the canopy can in principle be
replaced in the same way. In the canopy the starters are located
behind the lamps at the head of the canopy. To replace the
starters, you will first have to remove the tube lamps.
- Starters can be removed by turning them to the left.
- New lamps and starters and the acrylic sheet are assembled in
reverse direction and order.
- Do not forget to fasten the end cover with screws again.
• NB: The HPA lamps of the facial tanner may only be replaced by
authorised Philips service personnel.
Coin box or central control unit
This solarium can also be connected to a coin box or a central
control unit at the reception desk. These devices may only be
connected by a registered electrician. The connection instructions
can be found on a sticker on the power supply unit.
The environment
The lamps of solariums contain substances that can be harmful to
the environment. When you discard the lamps, make sure they are
not thrown away with the normal household waste but are handed
in at an official collection point.
7