Disposal Information; Declaration Of Conformity; Exemption From Liability - Flex L 602 VR Instrucciones De Funcionamiento Originales

Polisher L602VR
When the polisher is being used, the carbon
brushes can be seen sparking through the rear
air inlet apertures.
If the carbon brushes spark excessively, switch
off the polisher immediately. Take the polisher
to a customer service workshop authorised by
the manufacturer.
Gears
klqb>
aç=åçí=äççëÉå=íÜÉ=ëÅêÉïë=çå=íÜÉ=ÖÉ~ê=ÜÉ~Ç=
ÇìêáåÖ=íÜÉ=ï~êê~åíó=éÉêáçÇK=kçåJÅçãéäá~åÅÉ=
ïáää=ÇÉÉã=íÜÉ=Öì~ê~åíÉÉ=çÄäáÖ~íáçåë=çÑ=íÜÉ=
ã~åìÑ~ÅíìêÉê=åìää=~åÇ=îçáÇK
Repairs
Repairs may be carried out by an authorised
customer service centre only.
Spare parts and accessories
Spare-part/Accessory
Side handle
Handle cover
Bail handle
2 screws for bail handle
150 mm Velcro pad, damped
Velcro sponge, Ø 200 x 30 mm 304.778
Velcro wool pad
"FLEX-TopWool", Ø 195 mm
For other accessories, in particular tools and
polishing aids, see the manufacturer's
catalogues.
Exploded drawings and spare-part lists can
be found on our homepage:
www.flex-tools.com

Disposal information

t^okfkd>
oÉåÇÉê=êÉÇìåÇ~åí=éçïÉê=íççäë=ìåìë~ÄäÉ=
Äó êÉãçîáåÖ=íÜÉ=éçïÉê=ÅçêÇK
Only for EU countries
Do not dispose of electric tools
together with household waste
material!
In observance of European Directive
2012/19/EU on waste electrical and
electronic equipment and its implementation
in accordance with national law, electric tools
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling facility.
mäÉ~ëÉ=~ëâ=óçìê=ÇÉ~äÉê=~Äçìí=Çáëéçë~ä=çéíáçåë=
Ñçê=êÉÇìåÇ~åí=éçïÉê=íççäëK
We declare under our sole responsibility that
the product described under "Technical
specifications" conforms to the following
standards or normative documents:
Order no.
Responsible for technical documents:
252.721
FLEX-Elektrowerkzeuge GmbH, R & D
Bahnhofstrasse 15, D-71711 Steinheim/Murr
259.508
287.709
251.614
350.745
Eckhard Rühle
Manager Research &
Development (R & D)
350.265
25.01.2017
FLEX-Elektrowerkzeuge GmbH
Bahnhofstrasse 15, D-71711 Steinheim/Murr

Exemption from liability

The manufacturer and his representative are
not liable for any damage and lost profit due to
interruption in business caused by the product
or by an unusable product. The manufacturer
and his representative are not liable for any
damage which was caused by improper use
of the power tool or by use of the power tool
with products from other manufacturers.
klqb>

-Declaration of Conformity

EN 60745 in accordance with the regu-
lations of the directives 2014/30/EU,
2006/42/EC, 2011/65/EU.
Klaus Peter Weinper
Head of Quality
Department (QD)
19