Unloading Your Marker; Air Supply Cylinder Removal; Cleaning & Maintenance - Tippmann Triumph XL Manual Del Usuario

Model Specific Parts Not Shown on schematics (pages 10-11)
TRIUMPH XT and eXT
E
TA09932 Front Grip
N Assembly
11"
Barrel
G
L
I
98-40
S
Barrel
O-ring
H
In-Line
Expansion
Chamber/Gas
Line Assembly
TRIUMPH MARKER LINE SPECIFICATIONS
Model Basic ..................................................... TRIUMPH XL
Caliber ...................................................................................................... .68
Action ................................................. Semi-Automatic (open bolt blow-back)
Power/Air Supply ......................................... compressed air, nitrogen or CO
Hopper Capacity ...................................................................... 200 Paintballs
Ball Feed ............................................................................................ Gravity
Cycle Rate Triumph XL and XT ........................................ 8 shots per second
Standard Barrel Length Triumph XL ......................................................... 8.5"
Overall Length Triumph XL (with standard barrel & no tank) ...................... 19"
Weight Triumph XL (without tank) .................................................... 2.65 lbs.
Effective Range .................................................................................. 150+ ft.
Velocity ...... Always measure your marker's velocity before playing paintball
and never shoot at velocities in excess of 300 feet per second (see instructions
on page 7).
Model Specific .................................................. TRIUMPH XT
Standard Barrel Length Triumph XT .......................................................... 11"
Overall Length Triumph XT (with standard barrel & no tank) .................... 21.5"
Weight Triumph XT (without tank) ..................................................... 2.92 lbs.
Model Specific ................................................ TRIUMPH eXT
Cycle Rate ............................................................ Up to 15 shots per second
Standard Barrel Length Triumph eXT ........................................................ 11"
Overall Length Triumph eXT (with standard barrel & no tank) .................. 21.5"
Weight Triumph eXT (without tank) ................................................... 3.18 lbs.
TRIUMPH eXT Parts
TA01135 Sear
02-88 Sear Spring (Silver)
TA09939 Solenoid Pin
TA09935
Sear Tripper
Assembly
Solenoid
-Armature
fits inside
bottom of
solenoid
TA05014 Magnet
BY
Tippmann
BY Tippmann
BY
Tippmann
12

Unloading Your Marker

or completely empty the hopper. Then, point your marker in a safe direction
and fire several times to be sure there are no balls lodged in the chamber and
/ or barrel. Install barrel sleeve (see page 2). IMPORTANT: Do not uncock
your marker as uncocking your marker may push a ball into the chamber
or down into the barrel in which case the ball will be hidden from view.

Air Supply Cylinder Removal:

cylinder, turn the cylinder approximately 3/4 of a turn counterclockwise or out.
This allows the air supply pin valve to close so that no air will enter the marker.
Point the marker in a safe direction and fire the remaining gas in the marker by
pulling the trigger until the marker stops firing. This may take 4-5 shots.
• If your marker keeps firing after you have turned the tank 3/4 of a turn, the
tank pin valve has not closed yet and you may have to turn the tank
counterclockwise a little further.
• If you turn the tank 3/4 of a turn and it begins to leak before you pull the
trigger you have turned it too far and may have damaged the tank o-ring.
Because of the variances in tank valve parts, each tank varies slightly on
exactly how far it should be turned. If this process does not work the tank
®
pin valve could be too long.
NOTE: Before storing or disassembling be sure to remove paintballs and air
supply (see Unloading and Air Supply Removal instructions - see above.
2
Install barrel sleeve (see page 2).
Cleaning & Maintenance:
discharge: First follow unloading and air supply removal instructions
above and never disassemble a marker that is under pressure.
• Follow warnings listed on the air supply cylinder for handling and storage.
• Familiarize yourself with instructions listed on air supply cylinder or adaptor.
Contact the air supply cylinder or adaptor manufacturer with any questions.
• Do not use any petroleum based cleaning solvents.
• Do not use any cleaning solvents that come in aerosol cans. NOTE: Petroleum
based products and aerosol products can damage marker o-rings.
• To clean your paintball marker use a damp towel with water to wipe off
paint, oil, and debris. We recommend using Tippmann
®
other premium gun oil to maintain your marker in good working condition.
Re-oil with a few drops to the front bolt o-ring, rear bolt, barrel o-ring and
air tank o-ring.
front bolt o-ring.
• To clean the barrel: It is important to clean the barrel whenever you
®
break a paintball. Residue in barrel can cause more ball breakage and
poor performance. It is not necessary to remove the barrel from marker to
clean it. 1) Loosen the 2 hopper bolts
any paintballs in the chamber.
cleaning squeegee into the ball feed and push it through the barrel
until you can grab and pull the squeegee out of the barrel
to remove debris. Repeat as necessary.
:
To unload your marker remove the hopper
To remove a charged air supply
To reduce the chance of accidental
Remove the barrel to oil the barrel o-ring and
Oil rear bolt o-ring through the cocking slot.
, remove the hopper and
2) Insert the small end of the
13
E
N
G
L
I
S
H
® marker oil or