Technical Data; Safety Rules; General Power Tool Safety Warnings; Work Area Safety - Hilti TE 706 Manual De Instrucciones

4. Technical data

Power tool
Rated power input
Rated voltage
Rated current
Mains frequency
Weight of tool
Dimensions (L × W × H)
Chuck
Hammering speed under load
Single impact energy
Chiseling performance in medium-hard
concrete
Protection class
Right of technical changes reserved.

5. Safety rules

5.1 General Power Tool Safety Warnings

a) WARNING
Read all safety warnings and instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference. The
term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated
(cordless) power tool.

5.1.1 Work area safety

a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.

5.1.2 Electrical safety

a) Power tool plugs must match the outlet. Never mod-
ify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of elec-
tric shock.
b) Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Printed: 07.07.2013 | Doc-Nr: PUB / 5071189 / 000 / 00
TE 706/TE 706-AVR
1180 W
120 V
9.8 A
50–60 Hz
7.2 kg (15.9 Ibs)
560 × 125 × 250 mm (22 × 4.9 × 9.8 in)
TE-Y (SDSmax)
2760 blows/min
6–10 joules
750 cm 3 /min
I (grounded tool)
d) Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
g) Grounded tools must be plugged into an outlet prop-
erly installed and grounded in accordance with all
codes and ordinances. Never remove the ground-
ing prong or modify the plug in any way. Do not use
any adaptor plugs. Check with a qualified electri-
cian if you are in doubt as to whether the outlet is
properly grounded. If the tools should electrically
malfunction or break down, grounding provides a low
resistance path to carry electricity away from the
user.

5.1.3 Personal safety

a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influ-
ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
en
3