Cleaning And Maintenance; Spare Parts/Accessories - 3M MT15H7-WS6 Serie Manual De Instrucciones

4. SETUP MODE (fig. 10)
To access the setup mode, the headset must be turned off. Then
press and hold the On/Off/Mode button and Bluetooth
approximately 2 seconds to start the headset in setup mode.
Press and hold the [+] and [–] buttons for approximately
2 seconds to access the extended menu.To step through the
menu, press the On/Off/Mode button briefly. The menu steps
are listed below. At each menu step, the [+] and [–] buttons are
used to change the setting and step through the available
settings. A voice message confirms each menu step. After ten
seconds of inactivity, the menu returns to volume mode.
4:1 Bluetooth pairing
®
When the voice message says "Bluetooth
press (1 s) the [+] button to start pairing. Short press (1 s)
the Bluetooth button to stop pairing. A voice message will
®
confirm, "Bluetooth pairing on". Search and select "WS
®
ProTac XPI" on your Bluetooth
will confirm when pairing is complete, "pairing complete"
and "connected". Short press (1 s) the [–] button to stop the
pairing. A voice message will confirm, "pairing failed".
4:2 VOX (voice operated transmission)
VOX enables automatic transmission when the sound level
at the microphone is above the VOX level. This allows radio
transmission without pressing the Bluetooth
are two settings: off mode (default) and on mode for
activating voice operated transmission.
4:3 Battery type
Battery type adjusts the indication of low battery warning for
different types of battery. It is adjustable for two types of
batteries: rechargeable and alkaline.
4:4 Reset (reset to factory default) (fig. 9)
To confirm a reset to factory default, hold the [+] button for
2 seconds.
4:5 VOX mode
Enable or disable the VOX function.
NOTE: When disabled, this will not be availabe in the menu.
4:6 Automatic power off
The automatic power off is the time that elapses before the
headset is automatically powered off if no buttons are
pressed or if there is no transmission made. There are two
settings: off and 4 hours (default).
4:7 Bluetooth streaming
®
Enable or disable the streaming function. Disable is default.
4:8 Bluetooth Multipoint
®
Enable or disable the Multipoint function. Disable is default.
4:9 Microphone volume
Increase or decrease the microphone gain.
button for
®
pairing", short
®
device. A voice message
®
button. There
®
4:10 LED On/Off/Mode button
The On/Off/Mode button is illuminated by a Light Emitting
Diode (LED) which indicates that the headset is powered on.

5. CLEANING AND MAINTENANCE

Use a cloth wetted with soap and warm water to clean the
outer shells, headband, and ear cushions.
NOTE: Do NOT immerse the hearing protector in water.
If the hearing protector gets wet from rain or sweat, turn the
earmuffs outwards, remove the ear cushions and foam liners,
and allow to dry before reassembly. The ear cushions and
foam liners may deteriorate with use and should be examined
at regular intervals for cracking or other damage. When used
regularly, 3M recommends replacing the foam liners and ear
cushions at least twice a year to maintain consistent
attenuation, hygiene, and comfort. If an ear cushion is
damaged, it should be replaced. See "Spare parts/
accessories" below.
REMOVING AND REPLACING THE EAR CUSHIONS
L:1 To remove the ear cushion, slide your fingers under the
inside edge of the ear cushion and firmly pull straight out.
L:2 Remove existing liner(s) and insert new foam liner(s).
L:3 Fit one side of the ear cushion into the groove of the
earcup and then press on the opposite side until the ear
cushion snaps in place.
USE AND STORAGE CONDITIONS
Remove the batteries before storing the product. Do not store
the hearing protector at temperatures above 55 °C (131 °F),
for example on a dashboard, parcel shelf or window sill, or at
temperatures below –20 °C (–4 °F). Do not use the hearing
protector at temperatures above 50 °C (122 °F), or below 0
°C (32 °F).

6. SPARE PARTS/ACCESSORIES

3M™ PELTOR™ HY83 Hygiene kit
Replaceable hygiene kit. Replace at least twice a year to
ensure constant attenuation, hygiene, and comfort.
3M™ PELTOR™ HY80A Gel hygiene kit
Super-soft foam for enhanced comfort and high-temp
adhesive suited for hotter and more demanding
environments.
3M™ PELTOR™ HY100A Single-use protectors
Single-use protector that is easy to fit to the ear cushions.
3M™ PELTOR™ HYM1000 Microphone protector
Moisture- and wind-resistant tape that protects the speech
microphone.
3M™ PELTOR™ ACK053 Rechargeable battery pack
Rechargeable NiMH battery pack, 1900 mAh 2.4 V
Operating temperature range: 0 °C (32 °F) to 50 °C (122 °F)
6
EN