Grass Cutting - Stiga NJ 92 Serie Traducción Del Manual Original

Ocultar thumbs Ver también para NJ 92 Serie:
Tabla de contenido

Publicidad

Mechanical transmission
Push the pedal down as far as possible (see 
4.21) and move the gear change lever into 
1st gear (see 4.22).
Keep the pedal pressed down and disen-
gage the parking brake. Slowly release 
the pedal which will turn from «brake» to 
«clutch», thus operating the rear wheels
(see 4.21).
WARNING!
leased gradually, as a sudden engage-
ment may cause the vehicle to tip over
and the driver to lose control.
Gradually reach the desired speed using 
the throttle and gear lever. To change gear,
press the clutch halfway down (see  4.21).
IMPORTANT Gear must only be engaged
when the machine has stopped.
Hydrostatic transmission:
Disengage the parking brake and release 
the brake pedal (see  4.31).
Press the drive pedal (see  4.32) in direction 
«F» and reach the required speed by pro-
gressively increasing pressure on the pedal 
and moving the accelerator.
WARNING!
as described below (see 4.32) to prevent
sudden engagement from causing tipping
up and loss of control of the vehicle, par-
ticularly on slopes.
5.4.3 Braking
First reduce the machine's speed by reducing 
the engine's r.p.m., and then press the brake 
pedal (see  4.21 or 4.31) to slow down the ma-
chine until it stops.
Hydrostatic transmission:
The machine already slows down consider-
ably by just releasing the drive pedal.
5.4.4 Reverse
IMPORTANT Reverse must only be engaged
when the machine has stopped.
The pedal has to be re-
Drive must be engaged
IMPORTANT To proceed in reverse gear with
the cutting means engaged, it is necessary to
press and hold the consent button (see 4.7) so
as not to cause the engine to stop.
Mechanical transmission
Press the pedal until the machine stops and 
then switch into reverse by shifting the lever 
sideways and into position «R»  (see  4.22). 
Gradually release the pedal to engage the 
clutch and then begin moving in reverse.
Hydrostatic transmission:
When the machine is stopped, start the re-
verse movement by pressing the drive pedal 
in the «R» direction (see  4.32).

5.4.5 Grass cutting

Model 102
(Fig. 5.8) Adjust the position of the anti-
chipping wheels (1) whose function is to re-
duce the risk of tearing up sections of lawn, 
which can occur when the edge of the cut-
ting-means assembly drags over irregular 
ground.
The four different heights of the wheels allow 
you to maintain a safe distance «A» between 
the cutting-means assembly and the ground.
To change position, unscrew and extract 
the pin (1) and reposition the wheel (2) in 
the hole higher or lower than the row corre-
sponding to the wheel diameter.
WARNING!
performed on both wheels, position-
ing them at the same height WITH THE
ENGINE OFF AND CUTTING MEANS
DISENGAGED.
To start cutting:
–    m ove the throttle to «FAST»;
–    b ring the cutting-means assembly to the high-
est position;
–    e ngage the cutting means (see 4.7) only on 
grass lawns; avoid engaging them on stony 
ground or when the grass is very high;
–    s tart moving forwards on the grass very 
slowly and with utmost caution, as already 
described;
–    r egulate the cutting height and speed (see  
4.8) considering the conditions of the lawn 
(the height, density and dampness of the 
grass).
11
This should always be

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Nj 102 serie

Tabla de contenido