Cutting Line Replacement - Ryobi OLT-1823 Manual De Utilización

GB GB
F F D D E E
MAINTENANCE AND REPAIR
CAUTION
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.,
come in contact with plastic parts. They contain
chemicals that may damage, weaken, or destroy
plastics.

CUTTING LINE REPLACEMENT

The cutting line may be replaced by either rewinding the
existing spool or installing a convenient prewound spool.
REWINDING THE EXISTING SPOOL
See Figure 12.
Remove the battery pack from the string trimmer.
■
Press in the tabs on each side of the spool cap.
■
Remove the spool cap and spool. Discard any
■
remaining line on the spool.
NOTE: If the spring falls off the spool housing during
this procedure, reinstall the spring before installing
the spool and spool cap.
Inspect the string head for damaged or worn parts
■
and clean thoroughly.
Using approximately 3 m (10 feet) of new cutting line,
■
insert one end of the line into the slot on the spool.
Ensure the end of the line is pushed all the way
towards the inner side of slot.
NOTE: No more than 3.175 mm (1/8 in.) of the line is
to protrude from the slot.
Wind the line, in even and tight layers, onto the spool.
■
Line should be wound in the direction of the arrow
indicated on the spool.
Unwind approximately 102 mm (4 in.) of the line from
■
the spool. Hold the line and spool firmly to keep it from
unwinding then place the spool cap onto the spool.
Holding the spool cap and spool by the bump knob,
■
place into the spool housing and insert cutting line
into the opening in spool housing.
NOTE: Tabs on the spool cap should be aligned with
the slots in the spool housing.
While pressing in the tabs, push down the spool cap
■
and spool to lock in place.
Completely assembled string head should appear as
■
shown. See Figure 13.
I I P P NL NL S S DK DK N N FIN GR HU FIN GR HU CZ RU CZ RU
English
INSTALLING A PREWOUND SPOOL
See Figure 12.
Remove the battery pack from the string trimmer.
■
Press in the tabs on each side of the spool cap.
■
Remove the spool cap and spool.
■
NOTE: If the spring falls off the spool housing during
this procedure, reinstall the spring before installing
the spool and spool cap.
Inspect the string head for damaged or worn parts
■
and clean thoroughly.
Unwind approximately 102 mm (4 in.) of the line from
■
the prewound spool. Hold the line and spool firmly to
keep it from unwinding then place the spool cap onto
the spool.
Holding the spool cap and spool by the bump knob,
■
place into the spool housing and insert cutting line
into the opening in spool housing.
NOTE: Tabs on the spool cap should be aligned with
the slots in the spool housing.
While pressing in the tabs, push down the spool cap
■
and spool to lock in place.
Completely assembled string head should appear as
■
shown. See Figure 13.
CLEANING THE STRING TRIMMER
Remove the battery pack.
■
12
RO PL SLO HR TR EST LT RO PL SLO HR TR EST LT
WARNING
Use only 1.65 mm (0.065 in) diameter genuine
replacement line. Never use metal reinforced
line, wire, or rope, etc. These can break off and
become a dangerous projectile. Do not use any
other attachment on this unit.
WARNING
Do not attempt to modify this unit or create or
mount any accessory
recommended in this manual for use with
this string trimmer. Any such alteration or
modification is misuse and could result in a
hazardous condition leading to possible serious
personal injury. Examine string trimmer
frequently to assure all parts are unbroken and
securely attached. Make sure all screws and
fasteners are securely tightened to prevent the
risk of serious personal injury.
LV LV SK BG SK BG
not specifically