Descargar
Compartir
Imprimir esta página
  1. Manuales
  2. Marcas
  3. Moog Videolarm Manuales
  4. Accesorios para Camaras
  5. TOSHIBA JK-ACH13HBN
  6. Instrucciones de instalación y funcionamiento

Moog Videolarm TOSHIBA JK-ACH13HBN Instrucciones De Instalación Y Funcionamiento

Ocultar thumbs
1
2
3
4
5
6
7
8

Publicidad

Enlaces rápidos

Descargar este manual
Manufactured for:
TOSHIBA
by
Before attempting to connect or operate this product, please read these instructions completely.
PRODUCT INSTRUCTIONS:
Installation and Operation Instructions for the following model:
JK-ACH13HBN
Aluminum Outdoor Environmental Camera Housings
81-IN4507R1

Publicidad

loading

Manuales relacionados para Moog Videolarm TOSHIBA JK-ACH13HBN

Resumen de contenidos para Moog Videolarm TOSHIBA JK-ACH13HBN

  • Página 1 Manufactured for: TOSHIBA Before attempting to connect or operate this product, please read these instructions completely. PRODUCT INSTRUCTIONS: Installation and Operation Instructions for the following model: JK-ACH13HBN Aluminum Outdoor Environmental Camera Housings 81-IN4507R1...

  • Página 3: Electrical Specifications

    Electrical Specifications JK-ACH13HBN Input Power: 24 VAC; 35 Watts Power Output: 12VDC 15 Watts Camera: Not Supplied Tools Required: Phillips Screwdriver English 7/16 Wrench or Socket Energía De Entrada: 24 VAC; 35 Watts De Salida De Energía: 27 Vatios De Heater/Blower Cámara fotográfica: No provisto Herramientas Requeridas:...

  • Página 4: Unpacking The Product

    Unpacking the Product JK-ACH13HBN ONLY Remove the tilt mechanism from the bracket. Quite el mecanismo de la inclinación del • soporte. Enlevez le mécanisme d'inclinaison de la • parenthèse. Entfernen Sie die Neigungeinheit vom • Haltewinkel. Remova o mecanismo da inclinação do suporte. •...
  • Página 5 Remove the (2) screws on top of the Install the (2) cable strain relief plugs on the bottom of the housing and tighten with the locknuts. housing and lift it open. • Quite (2) los tornillos encima de la cubierta y levántelos •...
  • Página 6 INPUT 24Vac The beam angle may be adjusted on the These are recommended maximum distances Run 24VAC power through a conduit plug, and place the for 24VAC with a 10% voltage drop. bottom of the unit. stripped power wire ends into the 24AC power board. •...
  • Página 7 Close the top cover and tighten to the base with the If desired, use the security screws in place of hex hex screws. screws. • Cierre la cubierta superior y apriete a la base con los tornillos • Si está deseado, utilice los tornillos de la seguridad en lugar de de la tuerca hexagonal.

  • Página 8: Replacement Parts List

    Replacement Parts List Part Number Description RPACH010 ACH13 Front Endcap Assembly JK-ACH13HBN RPACH020 ACH13 Lid Screws ACH2 24V Heater & Thermostat Kit For ACH13 H12ACH12 12V Heater & Thermostat Kit For ACH13 RPACH050 ACH13 Camera Sled RPACH060 ACH13 Top Extrusion RPACH070 ACH13 Bottom Extrusion RPACHPK...