Tabla de contenido
Publicidad
FCC COMPLIANCY STATEMENT
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1)
This device may not cause harmful interference
2)
This device must accept any interference received, that may cause undesired operation.
Warning: Changes or modification to the equipment not approved by Laney can void the user's authority to use the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following
measures.
Reorient or relocate the receiving antenna.
!
Increase the separation between the equipment and receiver.
!
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
!
Consult the dealer or an experienced radio/TV technician for help.
!
This product conforms to the requirements of the following European Regulations, Directives & Rules:
CE Mark (93/68/EEC), Low Voltage (2014/35/EU), EMC (2014/30/EU),
RoHS (EU2011/65/EU),
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal
household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the WEEE
(Waste Electrical and Electronic Equipment) directive applicable in your country.
SPECIFICATION
:
A-DUO
Model
:
~100V to ~240V 50-60Hz
Supply Voltage
:
T3.15A L 250V
Mains Fuse
:
100W
Power Consumption
Output Power Rating: :
120W
Loudspeakers:
:
2 x 8" Custom Designed Full Range Coaxial Driver
Inputs:
: CH1/CH2 - Combi Balanced XLR
: CH1/CH2 - Mic/Line - Unbalanced 6.3mm jack
: CH1/CH2 - Mic/Line - Combi Balanced XLR
: Unbalanced 6.3mm jack
EQ:
: Bass:
: Middle:
: Treble:
:
Shape: 3 Band Preshape EQ
FX Channel1:
:
Reverb: Adjustable amount
:
Chorus: Adjustable amount
FX Channel2
:
Reverb: Adjustable amount
:
Chorus: Adjustable amount
Other
: Anti-Feedback control
:
Phase
D.I. Out
:
Balanced XLR with source switch and GND lift
Aux In
:
3.5mm Stereo jack
Headphones
:
3.5mm Stereo jack
:
(Speaker mutes when headphones are connected)
Pole cup :
For use with a standard 35mm pole stand (not included)
Unit dimensions (HWD) :
530 x 265 x 242mm, 20.9" x 10.4" x 9.5"
Net weight :
10.5Kg, 23.1 lbs
Carton dimensions (HWD) :
615 x 310 x 285mm, 24.2" x 12.2" x 11.2"
Gross weight :
12Kg, 26.5 lbs
Optional Extras:
: FS2-Mini Foot switch PN: FS2-MINI
In the interest of continued development, Laney reserves the right to amend product specification without prior notification.
--------------------------------------------------------------------------------
ErP (2009/125/EU).
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
Supports 15V Phantom Power
Impedance - 10M Ohm/47pF
Supports 15V Phantom Power
Impedance - 10M Ohm/47pF
±12dB at 100Hz, Lo Shelving
±12dB at 600Hz, Peaking
±12dB at 10KHz, Hi Shelving
Auto 12 Position notch filter
EN
Male XLR
6.35mm Mono Jack
6.35mm Stereo Jack
3.5mm Stereo Jack
Female XLR
A-DUO
1 GROUND
2 HOT
3 COLD
Mic
Line In, FX Send/Return
TIP
REVERB REMOTE
RING
CHORUS REMOTE
SLEEVE
GROUND
Remote
TIP
LEFT
RING
RIGHT
SLEEVE
GROUND
Aux In, Phones
1 GROUND
2 HOT
3 COLD
D.I. Out
9
Publicidad
Tabla de contenido
