DeWalt D27300 Manual Del Usuario página 27

Identifying the hardware parts (fig. B2)
We recommend that you unpack and sort all hardware parts.
14 Wheel bracket
15 Wheel axle
16 M8 coach bolt
17 M8 hex head bolt
18 M8 nut
19 Wing nut
20 D8 toothed washer
21 D8 flat washer
22 D8 flat washer
23 D8 Belleville washer
Mounting the feet (fig. C1 & C2)
With the feet mounted, the machine is suitable for placement on a workbench.
To ensure a safe operation, the machine has to be fixed to the workbench.
Required hardware parts: 4 nuts (18), 4 toothed washers (20) (fig. C1).
• Turn the machine on its side with the thicknessing outfeed frame (24)
resting on the floor (fig. C2).
Take care to avoid that the planing dept adjustment knob (10)
hits the floor.
• Insert a foot (25) into each of the outer notches (26) located in the
bottom of the machine housing.
• Place a toothed washer (20) and a nut (18) onto the threaded end of
the feet.
• Tighten the nuts.
• Turn the machine straight up.
• Fix the machine to the workbench.
Mounting the legs (fig. D1 - D3)
With the legs mounted, the machine is suitable for stand-alone placement.
Required hardware parts: 4 coach bolts (16), 4 wing nuts (19), 4 flat
washers (21) (fig D1).
• Turn the machine on its side with the thicknessing outfeed frame (24)
resting on the floor (fig. D2).
Take care to avoid that the planing dept adjustment knob (10)
hits the floor.
• Insert a leg (27) into each of the top holes (28) located at the edges in
the bottom of the machine housing.
• Pass a coach bolt (16) through the holes in the legs and the machine
housing.
• Place a flat washer (21) and a wing nut (19) onto the bolts.
• Tighten the wing nuts.
• Turn the machine on its side with the planing outfeed table (29) resting
on the floor (fig. D3).
• Repeat as for the other feet.
• Mount the castor wheels as described below.
Mounting the castor wheels (fig. E1 - E3)
Required hardware parts: 2 wheel brackets (14), 2 wheel axles (15), 2
bolts (17), 4 nuts (18), 2 flat washers (21), 2 Belleville washers (23) (fig. E1).
• Align each wheel (30) with a bracket (14) and pass a wheel axle (15)
through the holes of each assembly (fig. E2).
• Place a flat washer (21) and a nut (18) onto the threaded end of the axles.
• Tighten the nuts.
• Mount a wheel assembly (31) to each of the upper legs (32) using a hex
head bolt (17), Belleville washer (23) and nut (18) (fig. E3).
• Tighten the nuts.
• Turn the machine straight up.
Mounting the fence (fig. F1 & F2)
• Place the fence (8) onto the fence holder (33) (fig. F1).
• Pass a coach bolt (16) from underneath through the holder and the
fence.
• Place a flat washer (22) onto the bolt (16) (fig. F2).
• Fit the clamp handle (7) onto the bolt (16).
Mounting the guard (fig. G1 & G2)
• Insert the guard (13) into the guard column (34) (fig. G1).
• Locate the guard by fitting the lock screw (35).
• Fit the clamp handle (12) to the column (34) (fig. G2).
Mounting the shavings collector (fig. H1 & H2)
When using the machine in planing mode, the shavings collector has to be
mounted underneath the upper table. When using the machine in
thicknessing mode, the shavings collector has to be mounted on top of
the upper table.
Planing mode (fig. H1)
• Loosen the screws (36) a few turns to allow the shavings collector to
pass behind the head of the screws.
• Present the edges (37) on each side of the shavings collector to the
grooves (38).
• Slide the shavings collector (4) underneath the upper table (9), until the
recesses (39) locate behind the screws.
• Fix the shavings collector by tightening the screws.
Thicknessing mode (fig. H2)
• Loosen the screws (36) a few turns to allow the shavings collector to
pass behind the head of the screws.
• Place the shavings collector (4) upside over the upper table top (9).
• Slide the shavings collector (4) along the upper table (9), until the
recesses (39) locate behind the screws.
• Fix the shavings collector by tightening the screws.
Adjustment
Prior to adjustment always unplug the tool.
Adjusting the fence (fig. I1 - I3)
Adjusting the right angle (fig. I1)
The fence has an adjustable stop at for easy right angle adjustment.
• Loosen the angle clamp handle (40).
• Press the fence straight up to ensure it is fully vertical and tighten the
angle clamp handle.
• Place a set square (41) on the table and up against the fence (8).
• If adjustment is required, proceed as follows:
• Loosen the nut (42) a few turns and turn the vertical position
adjustment stop screw (43) in or out until the fence is at 90° to the
table as measured with the square.
Adjusting the chamfering angle (fig. I2)
• Loosen the angle clamp handle (40).
• Move the fence (8) along its longitudinal axle to achieve the required angle.
• Make sure that the lower edge of the fence touches the upper table
top (9).
• Tighten the angle clamp handle.
Adjusting the planing width (fig. I3)
• Loosen the fence clamp handle (7).
• Move the fence (8) accross the upper table (9) to achieve the required
width.
• Tighten the fence clamp handle.
B&D_17
E N G L I S H
27