Functions Turning On The Unit - PRESIDENT BARRY II Manual Del Usuario

nected to the rear panel of the transceiver (E) disables the original
microphone.
Press shortly the VOX key (8) in order to activate the VOX function.
«VOX» appears on the display. A new press on the VOX (8) key
disables the function, «VOX» disappears.
VOX SET
(long press)
1. Long press the VOX/SET key (8) to enter the VOX SETTING. "VOX"
blinks, the current setting and its value appear on the display.
Three parameters allow to adjust the VOX: Sensitivity: L / Anti-vox
level: A / Vox delay time: t.
2a. Use the s/t key (3) on the unit or the UP/DN key (12) on the mi-
crophone to modify the current parameter then, press the F key
(5) to select the next parameter or....
2b. Press first the F key (5) to select another parameter and then use
the s/t key (3) on the unit or the UP/DN key (12) on the micro-
phone to modify the current parameter.
3. When all adjustments are done, long press the PTT switch (11) to
store and exit. If the KEY BEEP function is activated, a long beep
sounds to confirm the success of the operation (see § KEY BEEP
page 35).
4. If no key is pressed for 10 seconds, the unit automatically exits the
function VOX SETTING without saving.
Sensitivity L: allows the adjustment of the microphone (original one
-
or optional vox) for an optimum transmission quality. Adjustable
level from L1 (high level) to L9 (low level). Default value: L5.
- Anti-Vox A: allows disabling the transmission generated by the
surrounding noise. The level is adjustable. AF (according the
squelch level) and from A0 (without anti-vox) to A9 (low level).
Default value: AF.
Delay time t: allows avoiding the sudden cut of the transmission
-
by adding a delay at the end of speaking. The level is adjustable
from t1 (short delay) to t9 (long delay). Default value: t1.
VOX SETTING doesn't activate the VOX function.
9) USB CHARGING SOCKET
The USB socket (9) can be used to charge a smartphone, tablet
or other rechargeable device with 5 V - 2.1 A.
10) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes
the setting of the equipment into the dashboard easier.
See cabling diagram page 67.
11) PTT (Push To Talk)
Transmission key, press to transmit a message,
release to listen to an incoming communication.
See FUNCTIONS WITH PTT SWITCH on page 35.
TOT (Time Out Timer)
If the transmission key is longer than 3 minutes, active channel and
start blinking, the transmission ends.
The time-out tone will sound until the PTT switch (11) is released.
12) CHANNEL SELECTOR: UP/DN knobs on the microphone
These keys allow increasing or decreasing a channel. A «beep»
sounds each time the channel changes if the KEY BEEP function
is activated. See § KEY BEEP page 35.
See also § 3 page 32.
A) DC-POWER TERMINAL (13.2 V / 26.4 V)
B) ANTENNA CONNECTOR (SO-239)
C) EXTERNAL SPEAKER JACK (8 Ω, Ø 3.5 mm)
D) PA SPEAKER JACK (8 Ω, Ø 3.5 mm)
E) OPTIONAL VOX MIKE (Ø 2.5 mm)
C) FUNCTIONS TURNING ON THE UNIT
5 more functions are available. Turn off the unit. Turn on the radio
while pressing one or two keys to set the function.
1) ROGER BEEP
(s key on the unit or UP knob on microphone)
The ROGER BEEP sounds when the PTT switch (11) of the microphone
is released in order to let your correspondent speak. Historically as
34
is displayed and