General Description; Processable Materials - IMER M400 SMART Manual De Uso, Mantenimiento Y Recambios

Dear Customer,
Congratulations on your choice of purchase: IMER saws are the result
of years of experience and are equipped with all the latest technical
innovations.
- WORKING IN SAFETY
To work in complete safety, read the following instructions
carefully.
To work in complete safety, read the following instructions carefully
before using the machine.
The manual is considered part of the machine and must be stored for
future reference (EN 12100-2) through to scrapping of the machine
itself. Should the manual be lost or damaged, a replacement copy can
be ordered from the manufacturer.
The manual contains important information regarding site preparation,
machine use, maintenance procedures, and requests for spare parts.
Nevertheless, the installer and the operator must both have adequate
experience and knowledge of the machine prior to use. In order to ensure
operator safety, safe operation and long service life, all instructions in
this manual must be observed, together with the requirements of current
legislation governing work safety (use of safety footwear and adequate
clothing, use of helmets, gloves, goggles etc.).
- Make sure that all signs are legible.
- It is strictly forbidden to carry out any form of modifi cation to
the steel structure or working parts of the machine.
IMER INTERNATIONAL declines all responsibility for failure to comply
with laws and standards governing the use of this equipment, in
particular; improper use, defective power supply, lack of maintenance,
unauthorised modi¿ cations, and partial or total failure to observe the
instructions contained in this manual.
IMER INTERNATIONAL reserves the right to modify features of the saw
and contents of this manual, without the obligation to update previous
machines and/or manuals.
1. TECHNICAL DATA
Technical data are stated in table 1 and electrical speci¿ cations in table
2.
Table 1 - TECHNICAL DATA
Model
Max. blade diameter
Diamond Blade hole diameter
Single phase 230V/50Hz motor power
Max. blade rotation speed (230V/50HZ)
Cutting table dimensions
Length of 90° cuts (thickness= 10mm)
Maximum cutting depth of dia. 350 disc with 1-2
passes
Maximum cutting depth of dia. 400 disc with 1-2
passes
Water pump À ow rate
Water tank capacity
Machine dimensions
Packed machine dimensions
Weight with packaging
IMER INTERNATIONAL S.p.A.
M400 SMART
2. DESIGN AND CONSTRUCTION STANDARDS
Combi 250 VA saws have been designed and manufactured according
to the following standards: UNI EN 12418:2001; EN 12100-1/2:2005;
EN 60204-1:2006.
3. NOISE LEVEL AND VIBRATIONS
Table 3 gives the sound pressure level of the machine measured at
the ear of the operator when running under no load (L
transmitted when it is operating.
4. GENERAL SAW DESCRIPTION

4.1 General description

The M400 SMART sawing machine is composed of a frame (Fig.1,
Ref.A)
Ref.C) is mounted to a pillar and can be rotated up and down through
32° by slackening off the handwheel (Fig.1, Ref.D). The sawing machine
is ¿ tted with a blade guard (Fig.1, Ref.E) to guarantee optimal safety
during operation and to protect the user during cutting cycles. The
carriage (Fig.1, Ref.F) used to support the material being cut runs on
the frame's rails. It mounts the goniometer (Fig.1, Ref.G) for making
cuts at different angles. A plastic impact-resistant tank (Fig.1, Ref.H) is
mounted under the frame. The immersion water pump (Fig.1, Ref.I) is
housed inside the tank and supplies water to the nozzles (Fig.1, Ref.L)
M400 SMART
mounted on the blade guard which cool the disc during cutting. A valve
230 mm
(Fig.1, Ref.M) is mounted above the blade guard to adjust the À ow rate
25.4 mm
of water delivered to the cutting
2.2 kW
2.800 rpm

4.2 Processable materials

510X410mm
The sawing machine has been designed for cutting the following
500 mm materials: brick, ceramic, marble, granite, articles in cement and similar
of a size compatible with the length, cutting depth and dimensions of the
107/204mm
table speci¿ ed in table 1. Maximum weight of processable materials:
35 kg.
129/250mm
13 l/min
40 L
1186x722x850 mm
1196x732x895 mm
77 (97) Kg
10
Table 2
Feature
Power (kW)
Rated voltage (V)
Frequency (Hz)
Absorbed current(A)
Number of poles
Motor speed (rpm)
Service type
Insulation class
Protection class
Capacitor (—F)
Table 3
Model Type of motor
M400 SMART Electric
supported by folding legs (Fig.1, Ref.B). The cutting head (Fig.1,
blade.
GB
Motor (230V/50Hz)
2.2
230
50
11.7
2
2800
S6 40%
F
IP55
40 (dia. 45x96)
) and vibrations
pA
L A
pA eq
86 dB 2.57 m/s 2