Publicidad
Idiomas disponibles
Idiomas disponibles
Tent Installation Instructions
Assembly Instructions
1. Unroll and spread the tent in the box. Position the tent screen
mesh door toward the open tailgate. Spread the tent out
uniformly to fit the entire box floor.
2. Locate the box tie-down loops behind the cab of the truck on
the lower part of the box wall. Attach the small hooks located
on the front corners of the tent floor to the two lower box tie
down loops.
3. Pull the side bungee straps up and over the box sides and
attach them to the undercarriage (Figure 1). Repeat for other
side. Adjust straps loosely. (4 straps per side).
4. Locate the three (3) bungee cords positioned between the
tailgate and truck box. Drop them down between the tailgate
and box. Locate the three (3) bungee cords at the end of the
tent that hang off the tailgate. Join corresponding mate hooks
together underneath the tailgate. (see Figure 2)
Remember- Do not pull hard on the bungee cords as this will
lead to damage. The tent will sit firmly in place with only a
minimum of tension.
5. Remove shock-corded fiberglass poles from their bag and
assemble all five to maximum length. There are four long poles
and one short pole.
Remember - Do not pull on the shock-corded fiberglass poles
during installation or they will disjoint and will become too
long to fit into the pockets. If a pole becomes disjointed, be
sure to re-seat the segments before continuing.
6. Take two (2) long poles and feed them through the nylon
sleeves running from corner to corner of box. Do not put in
corner pockets yet. (see Figure 2)
7. Take a long pole and feed it through the nylon sleeve at the
front of box. Do not put in pockets yet. (Front Pole - Figure 2)
8. Take a long pole and feed it through the nylon sleeve at the
tailgate. (Tailgate Pole - Figure 2)
Remember - Do not use excessive force when placing poles
into pockets because this may tear the pockets.
9. Insert the tailgate pole into its corresponding pocket.
10. Insert the front pole into its corresponding pockets. The front
poles must be under the corner poles.
11. Insert the corner pole ends into their corresponding corner
pockets. The tent must cover the corners and sides of the truck
box to prevent water intrusion.
12. The front of the tent must be placed over the truck's plastic sail
panel. The front cord goes between the metal body and plastic
sail panel to prevent water intrusion. (see Figure 1).
13. Insert short pole inside the tent just above the door. Feed the
pole into the pocket. Secure the pole to the underside of the
tent surface with velcro straps. Place the fly sheet over the tent.
Secure fly bungee cord hooks to corresponding rain fly hook
rings. Once the tent is setup, snug the straps at the side of the
box. (see Figure 3)
Important: When using the tent in the rain, the mid-gate of
the tent and the mid-gate of the vehicle should be closed to
prevent water intrusion.
Avalanche Bed Tent
14. After use, the disassembly of the tent is the reverse of installa-
tion. Fold the rain fly and put it into the toe bag. Disassembly
the shock-corded fiberglass poles and place them into their
storage sleeve. Tie the sleeve and put it into the tote bag. Fold
the sides of the tent into the middle of the tent and roll the tent
up from the back. Tie it with the tie straps and place it in the
tote bag.
Warning: Vehicle must remain stationary while the tent is
erected in the bed of the truck.
FRONT CORD
2
1
FIGURE 1 - SIDE STRAPS
CORNER TO CORNER POLES
FRONT POLE
FIGURE 2 - TAILGATE STRAPS
FLY
STRAP
FIGURE 3 - FLY INSTALLATION
88962254
PART NO.
6200 Grand Pointe Dr., Grand Blanc, MI 48439
3
4
TAILGATE POLE
3
2
1
FLY
STRAP
2
6
SHEET
OF
Publicidad
