Installation Instructions; Safety Instructions; System Components - STEINEL L 265 S Manual Del Usuario

Serie L 265_24spr 17.07.2008

Installation instructions

GB
Dear Customer,
Congratulations on purchasing your new STEINEL SensorLight
and thank you for the confidence you have shown in us. You
have chosen a high-quality product that has been manufactured,
tested and packed with the greatest care.
Principle
LED light corona and Power LED effect light
The LEDs are twilight controlled. Ideal for permanently illumi-
nating house numbers, for example. If preferred, also only in
response to movement.
Activation of low-energy bulb on detecting persons
When the mini-sensor detects a person, the low-energy bulb
comes "ON" for the period of time selected.
The integrated high-performance infrared sensor is equipped
with a double 360° sensor that detects the invisible heat emit-
ted by moving objects (persons, animals etc.).

Safety instructions

I During installation, the electrical wiring being connected
must be dead. Therefore, switch off the power first and use
a voltage tester to check that the power supply is discon-
nected.
I Installing the SensorLight involves work on the mains volt-
age supply. This work must therefore be carried out profes-
sionally in accordance with national wiring regulations and
electrical operating conditions. (
A
-ÖVE/ÖNORM E8001-1,

System components

Glass shade
Retaining screw
Light housing
Wall mount
LED corona of light
Power LED Effect Light
Mini-sensor unit (removes for ease of setting functions)
Sealing plug
Installation
The site of installation should be at least 50 cm away from
another light because heat radiated from it may activate the
system. To obtain the specified reach of 8 m, the sensor
should be installed at a height of no more than 2 m.
Connecting the mains and load supply lead (see illustration)
The mains supply lead is a 3-core cable.
L = phase conductor (usually black or brown )
N = neutral conductor (usually blue)
PE = protective-earth conductor (green/yellow)
If in doubt, a voltage detector must be used to identify the
lead; subsequently disconnect the power supply again.
11:01 Uhr Seite 10
Please familiarise yourself with these instructions before
attempting to install the SensorLight because prolonged reliable
and trouble-free operation will only be ensured if it is fitted
properly.
We hope your new STEINEL SensorLight will bring you lasting
pleasure.
The heat detected in this way is converted electronically into a
signal that switches the light "OFF" automatically. Heat is not
detected through obstacles, such as walls or panes of glass.
Heat radiation of this type will, therefore, not trigger the sen-
sor. The unit achieves a coverage angle of 360° with an aper-
ture angle of 90°. A sneak-by guard ensures coverage below
the sensor.
Important: The most reliable way of detecting motion is to
install the SensorLight with the sensor aimed across the
direction in which a person would walk and by ensuring that
no obstacles (such as trees and walls, for example) obstruct
the line of sensor vision.
Reach is limited when walking directly towards the light.
I Only use genuine replacement parts.
I Repairs must only be made by specialist workshops.
I The glass shade
D
- VDE 0100,
-SEV 1000)
Connect the phase conductor (L), neutral conductor (N) to the
terminal block. Getting the cable connections crossed will
produce a short circuit in the unit or in your fuse box. In this
case, you must identify the individual cables and re-connect
them. Insulate protective-earth conductor (PE) and simply
place it next to terminal block.
Note: A mains switch for switching the unit ON and OFF may
of course be installed in the mains supply lead. A mains
switch is required for the manual override function (see Manu-
al override function)
- 9 -
must be screwed firmly onto the light
housing with the sealing ring
Sealing ring
8.1
Engagement lug for removing sensor unit
Time setting
Twilight setting
Programme setting
Principle
Adjusting the detection zone
Manual override
.
.
8.1