Black and Decker HP9012 Manual De Instrucciones página 6

ENGLISH
To lock the tool, set the forward/reverse slider into the
centre position.
Drilling/screwdriving (fig. A)
Select forward or reverse rotation using the forward/
reverse slider (2).
To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
To switch the tool off, release the switch.
Setting the torque
This tool is fitted with a collar to set the torque for tightening
screws. Large screws and hard workpiece materials require a
higher torque setting than small screws and soft workpiece
materials. The collar has a wide range of settings to suit your
application.
Turn the collar to the desired setting. If you do not yet
know the appropriate setting, proceed as follows:
- Set the collar to the lowest torque setting.
- Tighten the first screw.
- If the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
Hints for optimum use
Drilling
Always apply a light pressure in a straight line with the
drill bit.
Just before the drill tip breaks through the other side of
the workpiece, decrease pressure on the tool.
Use a block of wood to back up workpieces that may splinter.
Use HSS drill bits when drilling in metal.
Use a lubricant when drilling metals other than cast iron
and brass.
Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
Always use the correct type and size of screwdriver bit.
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
Always hold the tool and screwdriver bit in a straight line
with the screw.
When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw.
A pilot hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
6
When screwing in hardwood, also drill a clearance hole
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table below.
Screw size
No. 6 (3.5 mm)
No. 8 (4 mm)
No. 10 (5 mm)
Screw size
No. 6 (3.5 mm)
No. 8 (4 mm)
No. 10 (5 mm)
Screw size
No. 6 (3.5 mm)
No. 8 (4 mm)
No. 10 (5 mm)
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to high
quality standards and designed to enhance the performance of
your tool. By using these accessories you will get the very best
from your tool. This tool uses screwdriver bits and drill bits
with a 1/4" (6.35 mm) hexagonal shank. Piranha Super-lok
accessories are designed for use with this tool.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
set the forward/reverse slider to the centre position.
Unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Pilot hole ø (softwood)
2 mm
3.2 mm
3.5 mm
Pilot hole ø (hardwood)
2.5 mm
3.5 mm
4.0 mm
Clearance hole
4 mm
5.0 mm
5.7 mm