Stanley FATMAX SFMCS701 Manual Del Usuario página 18

ENGLISH
9
10
The chart assumes that all sides are of equal length. For a
shape that is not shown in the chart, use the following formula:
180º divided by the number of sides equals the mitre (if the
material is cut vertically) or bevel angle (if the material is cut
laying flat).
Cutting compound mitres (fig. R3)
A compound mitre is a cut made using a mitre angle and a
bevel angle at the same time. This is the type of cut used to
make frames or boxes with slanting sides like the one shown
in figure R3.
Note: If the cutting angle varies from cut to cut, check that
the bevel lock knob and the mitre lock handle are securely
locked. These must be locked after making any changes in
bevel or mitre. The chart at the end of this manual (Table 1)
will assist you in selecting the proper bevel and mitre settings
for common compound mitre cuts. To use the chart, select the
desired angle A (Fig. R3) of your project and locate that angle
on the appropriate arc in the chart. From that point follow the
chart straight down to find the correct bevel angle and straight
across to find the correct mitre angle.
Set your saw to the prescribed angles and make a few trial
cuts. Practice fitting the cut pieces together until you develop
a feel for this procedure and feel comfortable with it.
Example: To make a 4-sided box with 26º exterior angles
(Angle A, Fig. R3), use the upper right arc. Find 26° on the arc
scale. Follow the horizontal intersecting line to either side to
get mitre angle setting on saw (42°). Likewise, follow the
vertical intersecting line to the top or bottom to get the bevel
angle setting on the saw (18°). Always try cuts on a few scrap
pieces of wood to verify the settings on the saw.
Cutting base moulding (fig. S)
Straight 90º cuts:
Position the wood against the fence and hold it in place as
shown in Figure S. Turn on the saw, allow the blade to reach
full speed and lower the arm smoothly through the cut.
Cutting base moulding up to 3.5" (90 mm) high
vertically against the Fence
Position material as shown in Figure S. All cuts should be
made with the back of the moulding against the fence and with
the bottom of the moulding against the table.
Inside Corner
Mitre left 45°
Left Side
Save left side of cut
Mitre right 45°
Right Side
Save right side of cut
18
(Original instructions)
20°
18°
Outside Corner
Mitre right 45°
Save left side of cut
Mitre left 45°
Save right side of cut
Material up to 3.5" (90 mm) can be cut as described above.
Cutting crown moulding
In order to fit properly, crown moulding must be compound
mitred with extreme accuracy.
The two flat surfaces on a given piece of crown moulding are
at angles that, when added together, equal exactly 90°. Most,
but not all, crown moulding has a top rear angle (the section
that fits flat against the ceiling) of 52° and a bottom rear angle
(the part that fits flat against the wall) of 38°.
Your mitre saw has special preset mitre detent points at 31.6°
left and right for cutting crown moulding at the proper angle.
There is also a mark on the bevel scale at 33.8°.
The Bevel Setting/Type of Cut chart gives the proper settings
for cutting crown moulding. (The numbers for the mitre and
bevel settings are very precise and are not easy to accurately
set on your saw.) Since most rooms do not have angles of
precisely 90°, you will have to fine tune your settings anyway.
Instructions for cutting crown moulding laying flat
and using the compound features
Lay the moulding with broad back surface down flat on
u
saw table (36) (fig. T1).
The settings below are for all Standard crown moulding
u
with 52° and 38° angles.
Bevel Setting
33.8°
33.8°
33.8°
33.8°
Note: When setting bevel and mitre angles for all compound
mitres, remember that the angles presented for crown
mouldings are very precise and difficult to set exactly. Since
they can easily shift slightly and very few rooms have exactly
square corners, all settings should be tested on scrap
moulding.
Alternative method for cutting crown moulding
Place the moulding at an angle between the fence (11) and
the saw table (36), with the top side of the moulding on the
table and the bottom side of the moulding on the fence as
shown in figure T1.
The advantage to cutting crown moulding using this method is
that no bevel cut is required.
Type Of Cut
LEFT SIDE, INSIDE CORNER:
1. Top of moulding against fence
2. Mitre table set right 31.62°
3. Save left end of cut
RIGHT SIDE, INSIDE CORNER:
1. Bottom of moulding against fence
2. Mitre table set left 31.62°
3. Save left end of cut
LEFT SIDE, OUTSIDE CORNER:
1. Bottom of moulding against fence
2. Mitre table set left 31.62°
3. Save right end of cut
RIGHT SIDE, OUTSIDE CORNER:
1. Top of moulding against fence
2. Mitre table set right 31.62°
3. Save right end of cut