Makita UM600D Manual De Instrucciones página 15

NOTICE:
Do not pull the switch trigger forcibly
without pressing the lock-off button. The switch
may break.
Fig.3: 1. S w it c h trigger 2. Lock-off button
To start the tool, press the lock-off button and pull the
switch trigger. Release the switch trigger to stop. The
lock-off button can be pressed from either the right or
le f t si d e.
Indicator lamp
The indicator lamp blinks or lights up when the remain-
ing battery capacity is low or empty. The indicator lamp
also lights up when the tool becomes overloaded.
Fig.4: 1. I n d i c ator lamp
Lamp status and action to be taken
I nd ic ator lamp
The lamp blinks The remaining
battery capacity
red .
is low .
The lamp lights up The tool has
stopped because
red . *
th e remaining
battery capacity is
empty .
The tool has
stopped d ue to
ov erload .
The time at which the indicator lamp lights up varies depending
on the temperature around the work area and the battery car-
trid ge c ond itions.
Adjusting the shearing height (for
grass shear)
CAUTION:
W hen changing the shearing
height, be sure to attach the blade cover and be
careful not to trap fingers between the tool and
grass receiver.
The shearing height can be set to three levels (
mm, and mm) by changing the fixed position of
the grass receiver. The shearing height without the
grass receiver is about
1. S li d e t h e grass re c ei v er to w ar d t h e f ront o f t h e
tool.
Fig.5: 1. G rass re c ei v er
Change the fixed position of the grass receiver by
2.
mo v ing it in t h e d ire c tion o f t h e arro w .
Fig.6
NOTE: The shearing height value is a guideline. The
a c tual s h earing h eig h t ma y v ar y d epen d ing on t h e
c on d ition o f t h e la w n or t h e groun d .
NOTE: Try a test shearing in a less conspicuous
pla c e to get y our d esire d h eig h t.
Action to be taken
S tatus
Charge the battery.
Charge the battery.
Turn off the tool.
mm.
ASSEMBLY
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
always wear gloves and attach the blade cover so
that your hands and face do not directly contact
the blades.
NOTICE:
W hen replacing the shear blades, do
not wipe off grease from the gear and crank.
Installing or removing the blade
cover
CAUTION:
when installing or removing the blade cover.
To remove the blade cover, pull it slightly, and then slide
it sideways. To install the blade cover, perform the steps
in re v erse.
Fig.7
Installing or removing the grass
receiver
CAUTION:
grass receiver, be sure to attach the blade cover
and be careful not to trap your fingers between
the tool and grass receiver.
Removing the grass receiver
1. R elease t h e protrusions on t h e grass re c ei v er
f rom t h e groo v es on t h e tool w h ile sli d ing t h e grass
re c ei v er to w ar d t h e f ront o f t h e tool.
Fig.8: 1. G rass re c ei v er
2. R elease t h e h inge o f t h e grass re c ei v er f rom t h e
mm,
tool.
Installing the grass receiver
1. H ook t h e h inge o f t h e grass re c ei v er on t h e groo v e
o f t h e tool.
Fig.9: 1. H inge 2. G rass re c ei v er
Align the protrusions on the grass receiver with
2.
the grooves on the tool by sliding the grass receiver
to w ar d t h e f ront o f t h e tool an d mo v ing it in t h e d ire c tion
o f t h e arro w .
Fig.10
NOTICE:
Do not attach the hinge of the grass
receiver to the tool forcibly after aligning the pro-
trusions on the grass receiver with the grooves
on the tool.
15 ENGLISH
Always be sure that the tool is
W hen replacing the shear blades,
Be careful not to touch the blades
W hen installing or removing the