Electrical Safety - Black and Decker BDPSE3615 Manual De Instrucciones

Electrical safety

Symbols on the charger
+
Read all of this manual carefully before using the
#
appliance.
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
$
corresponds to the voltage on the rating plate.
The charging base is intended for indoor use only.
Labels on appliance
+
The following symbols appear on this appliance along with the
date code
Read all of this manual carefully before
using the appliance
se charger 90616337-01
S010Q 23
90616337-01
Features
This tool includes some or all of the following features.
1. On/Off button
2. 3 speed power switch
2a. Beater bar activation button
3. State of charge indicator
4. 36V Battery
5. 36V charger
6. Lift away dust canister with filter agitator
7. Dust canister door
8. Floor head
9. Extension tube
10. 2 in 1 Accesssory tool
11. Crevice tool (available to order through your service
department)
12. Accessory storage clip
13. Pet hair tool (available to order through your service
department)
14. Wide mouth dust brush (available to order through your
service department)
15. Hang hook for use with wall storage bracket (5a)
Charging a Battery
BLACK+DECKER chargers are designed to charge
BLACK+DECKER battery packs.
Note: To ensure maximum performance and life of lithium
ion battery packs:
Charge the battery pack fully before first use.
u
Recharge discharged batteries as soon as possible
u
after every use.
(Original instructions)
Do not discharge batteries fully.
u
Charging (Fig. A)
Plug the charger (5) into an appropriate outlet before
u
inserting the battery pack (4).
Insert the battery pack into the desk charger (5).
u
When using the the desk charger a green LED (5b) will
u
flash indicating that the battery is being charged.
The completion of charge is indicated by the green LED
u
(5b) remaining on continuously. The pack is fully charged
and may be used at this time or left on the charger.
Note: The battery includes a state of charge indicator to quick-
ly determine the extent of battery life. By pressing the state of
charge button (4a) you can easily view the charge remaining
in the battery.
To install battery pack (fig. B)
Insert battery (4) into tool until an audible click is heard as
u
shown in figure B.
Ensure battery pack is fully seated and fully latched into
u
position.
To remove battery pack
Depress the battery release button and pull battery pack
u
(4) out of the tool.
Assembly (Fig. C)
Align the top of the extension tube (9) with the vacuum
u
inlet (16) as shown in figure C.
Push the extension tube (9) onto the vacuum inlet (16) so
u
it locks into position.
Align the bottom of the extension tube (9) with the floor
u
head (8) as shown in figure C.
Push the bottom of the extension tube (9) onto the floor
u
head (8) so it locks into position.
To remove an accessory, press the accessory release
u
latch located on the accessory and pull it off.
USE
This vacuum cleaner can be used in one of four ways.
With the extension tube (9) and the floor brush (8) as
u
shown in figure C.
With the floor brush (8) and the vacuum inlet (16) as
u
shown in figure D.
With the extension tube (9) and an accesssory tool (10),
u
(11), (13) or (14) as shown in figure E.
With an accesssory tool (10), (11), (13) or (14) and the
u
vacuum inlet (16) as shown in figure E.
Accessories not supplied with your unit can be ordered
u
through service department.
Switching ON and OFF (Fig. F)
To switch ON, press the On/Off button (1).
u
ENGLISH
7